Видео

😡 Je l'ai utilisé sur un WV T3 : j'ai du re démonter la boite: Tous les plans de joint fuyaient ! Un grosse M...

Is the yellow liquid OIL from the engine to keep the pump lubricated ?

Curil T2 on the rocker area head washers/nuts and pushrod tube seals. Do NOT use paper gaskets under cylinders as per VW.

My fail-safe T stat doesn't come with a gasket.

أين تقع تريخ صنع في سليكون Dirko HT

Hello I really enjoy watching your videos and i like the work you do . Can you do me a favor and please let me know where can i find this engine stand that you’re using, can you send me the reference number for this repair engine stand . Thanks Kind Regards

Definitely too much silicone was applied to the oil pan!

Cool job colleagues

Bravo colleagues

Elring made an unintentional asmr...

What does the picture at 1:38 min mean? Is it basically once the seal is on the crankshaft, can't re do it again, take it off and re install it? Thanks

Hello. What is the square block tool called that he scrapes over the cylinder head and block?. He aplies cutting oil i asume?

Dont forget to put a new diamond washer everytime you remove camshaft cog

Do not buy beru made in Turkey, they are not of good quality. I bought it and it was defective in the manufacture and they did not want to change it

For the oil pans, do you apply the specified torque immediately after hand tightening or some time (and how much time) after hand tightening?

Actros 1842 aracım kartel çatlattı bu arıza kronik mis ama Mercedes servisi ancak ücret karşılığı değişeceğini soyledi

What was the toll name/brand used to scrap the old gasket sealer and the prep spray?

It’s probably already mentioned by someone else but there are a few mistakes in this video. If you loosen the crank shaft bolt you need to lock and fixate the crank shaft in the correct position using a specific tool when tightening to get the timing right. But in the first place, you don’t loosen the bolt for the work shown in this video. What you could do is to lock the crank shaft with the proper tool, only to be sure it doesn’t move during this work. You can’t tightening the crank bolt using two bolts and a metal shaft, the bolts would bend or break, you would need the proper tool. The instructor is tightening it by far too little. Maybe you should remove this video before someone copies this and mess up their engine.

I just ordered this valve cover from Elring for a fair price. I hope it is good quality. The bad thing is that they only offer 2 years warranty on this part in Europe. I replaced pcv valve and It didnt fix my rough idle problem and I still have vacuum problem at the oil cap. I hope by changing the valve cover will fix this problem !

Everything go wrong when you try to repair this engine because they want only them would touch it .

Comment tient le pignon de distribution en place sans son axe ?

💪❤👍

Love it 👍 well done guys. thanks 🙏

Wonderful 👍

Couplé de serrage moteur fiât 1.3 multijet

12 newton dogrumu

Tengo un panda 1.3 multijet diesel del 2004 con 400 mil km, pero ya se reparó el motor,, hace 4 días,, partió un árbol de levas y se lo cambiamos y terminamos de armar,, pero no arranca,, desarme y todo esta bien me queda solamente ver cigueñal,,, recuerdo que es en cuba donde tengo muy pocas piezas,, alguien sabe que puede estar ocurriendo. Gracias

Pretty good video, even though there is not any verbal audio. I like how you show a lot of the common areas of build up, it shows why you can still have issues after replacing just the pcv valve. I just ordered one from FCP Euro, so I hope that it performs like the OEM... or hopefully better. My car is building up vacuum and making a squealing sound.

How to remove this sealing after it is fully cured?

Спасибо большое за видео и вашу продукцию

Why does there 5 exhaust ports?? I cannot understand where the 5th leads.. it's a 4 cylinder?

Big thumbs-up 👍

Your parts are junk they have cost me so much money and I won't buy any more of mororad parts

thanks for showing this but what a stupid design engine it is

Hi, I have a Fiat punto 1.3 mtj the other day I accelerated from a standstill up to 4500 rpm all of a sudden the car accelerates by itself up to 5000 rpm smoke from the engine and exhaust pipe. I switch off the engine but it still stays on for approx. 15-20 sec. What may have happened ?? Please help me

JTD the best diesel!

Well done guys 👍

Thank you Elring ! for making quality gaskets and materials ..

Bom poder contar com um produto homologado e que passou por testes com quem fará o uso final . com demonstração então ..... Ganhamos mais confiança Grato.

Great, as some other people commented it would be a complete clip if torque settings and angles were shown to. I like using Elring products as they are top quality....

How to order ?

Awesome

Big thumbs-up 👍 💯

please can you tell me how much Nm you tightened the screws on the turbine and on the pipe thank you very much

Clean workshop and professional mechanic 👍

Maybe I'll order this next time instead of lock tite

I actually wanted to see the video with all the parts connected... That's easy like that

Perfect ☆☆☆☆☆

Hello is there any gap between vane and housing/body.

What about difference between Dirko Ht red and grey? Stihl recommends red but what about grey in same places?