Видео

Definitely worth doing this.!!! Although, I removed the whole lot. Cleaned it spotless, and replaced it with a K&N Apollo filter. SO much more room and LOADS better airflow, MUCH less risk of rust from that wet sponge and build up of dirt in the wing. Cold start may be an issue in cooler climates but, I haven't noticed any difference.

Sat by side of road trying to fit the only bit you didnt show 😅 👍

Cracking tip

I have this problem, so you video is perfect. Can you tell me where I can buy new same things as you bought to fix this problem?

I’ve tried boiling ours and drilling the hole a bit bigger still can’t get it on bloody things a nightmare 😂😂

Is the plastic undertray realy less noisy? and why? Think i might have to try that as a 1993 is quite loud haha. Just dont understand why it reductes the noise. Less klonky than metal? Taahnsk!

I wonder where the water will be captured? Usually there is a holding for water right.

Speak more clearly and slowly if you want people to understand you as I had to put on the captions. Yeah I know you guys spoke it first but you are speaking to Americans sometimes and directions must be considered because you sound like you got a mouth full of mush

Brilliant video, No annoying music straight to the problem very helpful. My T4 has suddenly got a slopy gear stick and can only get high gears and reverse so in the morning will go for it and check it out and just hope this is the problem and not gear box issues. Thanks again mate.

My old socks have got holes in them. Sigh.

Lovin it..! 👍👍😎👌

Found this video VERY useful, Haynes & Brooklands manuals lacking in any detail, of this most common bush failure, mine has done 175k miles, never had problem with gear linkage before, & VW T4 specialist had van in for clutch replacement (slave cylinder fail) in January this year, and asked for linkage bushings to be checked & replaced as necessary, 300 miles later that bushing failed in traffic jam, could not find 1st! got to destination (Nick Masons Garden Party) ok in 2nd. and home on M4/5 - all other gears selected ok - I think I was lucky........ I did not think the JK replacement ball bush would go over the end of the shaft, but heated it up in a saucepan of water on hob in back of van, picked it out with adjustable jaw pliers with an 'o' ring on handles to keep grip on it, then greased shaft (held in upward position to stop it flopping around by a 1/2" drive socket 3/4" placed on top of selector plate & under gear shaft) and using 21mm or 13/16" 1/2" drive socket on knuckle bar, taped in right angle position, used this rather than crow bar to lever it onto the shaft (clunk!) on it went, My van has Air - con, so even less space to operate... lubed up the other joints with grease & gear lever linkage with WD40. all good again. thanks for the video, it was a good learning curve....P.S. we got the ailing T4 into the Super Car Paddock-we were supporting the T.I.P.E.C. Porsche club as we had a display of 32 1/43th Porsche models on the dashboard + Porsche badge! there was also a 1971 Avis Transit & '63 Land/Rover there, so the T4 raised the standard on the Van front!

frozen chips?.....I'm OUt

This is exactly what's wrong with my t4. I'm not particularly experienced with mechanics and this video was spot on for me with explaining the aspects of the repair etc. Thanks allot!!! Subbed.

Is this also for the long nose?

Cheers for the info, i don't have the light but my sensor is leaking so I'll replace it when i change filter.

Great video. Do you have a video of how to change the 5th gear synchro ring on a 2.5 TDI. Cheers

Thank you sooo much for making these. Manuals available are crud.

.ynñhhh0t0tt0my0t0😅😊😊😊😊😊

.ynñhhh0t0tt0my0t0😅😊😊😊😊😊

I'm wondering if it would have any effect if you put your kitty liter, etc, into an aluminum treated for diabetes sock. As you may know they are sold to keep feet dry.

A useful video but it would be helpful to know the location of the sensor. I assume it's underneath the engine? I can't see mine because of the engine guard.

That doesn't look anything like the inside of a VW

The real PITA is to change the plastic bed where the smaller (left)ball is mounted.

Do you have the reference? Your link is down

Awesome video! I had a look under the hood after realizing my 5th gear was having a hard time switching and found out my linkage looked exactly same as yours. I will definitely order a kit and do this.

Hey! I've got an old sock! 😃

Use silicone grease,not petroleum jelly (vaseline) as I think vaseline will make the silicone ball and joint perish.I also occasionally spray these parts with silicone spray.So far,they are still ok 8 years later.

Great idea😊 Thank you❤

CAN TELL YOUR NOT A CHEF........ it,s camping everything goes into the RIDGEMONKEY and cooks at same time .........and why the polybag the chips go into the pan and get seasoned (THE RIDGEMONKEY) .......ALONG WITH EVERYTHING ELSE .

Thanks

Any way to do it without spilling the crap all over the engine and ground 🤔

Great video, did my yesterday cheers 👏👏🤙

Just brought a tray from Brickworks, Great video, just what I needed. Thanks

Would a pure silica cat litter work better? Would putting it in a jar with holes in lid contain any water absorbed? Been looking all over Internet for this information. Haven't found anything that shows results.

Bravo 👏

no link from where you got them........

HEY NICE VIDEO :) HAVE THE SAME PROBLEM AND BOUGHT NEW BUSSING BUT SEEMS TO SMALL. WHAT DIAMETER DID YOU BY? mine is 19 mm but the hole in the middle wont fit. I HAVE A VW CARAVELLE 2.5 PETROL 2000 TANK YOU

Been thinking of fitting one to my VW T5. Seeing this I have decided to do so.

Ive put the wrong coolant in , can I use your method to empty it/flood it through with correct coolant

hi there how and where did you attach the tv bracket please ?

Great idea! Thanks for sharing

add a little Loctite to any threads .

I bought a set of these for mine but they didn't fit right. Think it was because I have new front wings fitted and not original. I'm going to fit some of those quick release bonnet pins on the grill to stop it rattling about 😉

and the sugar in the mix ,no???

It was good until you suggested to DRY IT ON THE RADIATOR-this will evaporate all the water back into the air again!!!!!!!!! Defeats the object! YOU NEED TO COLLECT THE WATER AND GET RID!!!Or am I missing something???!!!🤣😂🤣

Спасибо за видео.

Really appreciate your clear video, I’m going to attempt mine, lost 5th and 1st gear after leaving Isle of Wight but just made it back to newhaven with 3 gears, i like an adventure .👍🏼

Looks disgusting and probably tastes disgusting as well - processed junk!

Good video footage, easy explanation. Thank you. Now I know the parts division only gave me half of the adjusters (not the inner upper one - DAMN)