![DooKamonN](/img/default-banner.jpg)
- Видео 38
- Просмотров 24 942
DooKamonN
Добавлен 10 июн 2011
Hi, I want to thank all of YOU for viewing my channel. Trust that I will release very entertaining content. YOU ALL will not be disappointed. SPREAD THE ENTERTAINMENT!!!
Enjoy!!
Enjoy!!
Torquing down my LS3 821 heads, rockers, and explaining how I found my PTV clearance
Torque baby torque we finally got a chance to torque down these heads for the final time i'm praying these heads never ever ever have to come back off. I used 821 LS3 heads with ARP head bolts, LS9 head gaskets, stock valves, CHE bronze bushing trunion upgrade with stock rocker. In the end I explained how I found my piston to valve clearance
Просмотров: 41
Видео
I cut my finger really bad on a LS9 head gasket
4 часа назад
I don't know why I never thought of head gaskets being sharp, but I learned the hard way. You got to be careful when you're dealing with them because I completely sliced up my finger just trying to get them out of the plastic.
Installing my 660 BTR valve spring kit in my 821 LS3 heads
Просмотров 2421 час назад
This was the SK001 BTR 660 valves ring kit with steel retainers For an LS3 head
Timelapse of me cleaning my 821 LS3 heads No water
Просмотров 10014 дней назад
Pretty much what the title says I decided to film a little time lapse of Me cleaning the heads off. All I used was mineral spirits in a zip chemical sprayer bottle and I used brake cleaner to wash everything off. I used a regular small brush that you buy in the cleaning aisle of Walmart or anywhere. I used some engine cleaning brushes from Moroso to get into all the Knicks and crannies and valv...
First look at my LS3 821 ebay bought heads
Просмотров 13921 день назад
I bought these used heads from an ebay seller. Of course, I was worried about getting screwed over but from the pictures, reviews, and description I decided to take a chance.
Finishing off the short block. Installing the pick-up tube, front & rear covers, etc.
Просмотров 10328 дней назад
Right after finishing up the Rotating assembly & cam, I went on to top off the bottom end I ended having to order more windage tray bolts from eBay, but everything worked out fine
Installing my last piston & rod into my ls3
Просмотров 148Месяц назад
I made sure I did the other pistons first so I could have my technique down for this last one. Also, I bought a piston ring installer tool but that ish didn't work for me I just used my hands. Buy it anyway because you will need it to take rings off.
Final torque of my LS3 crankshasft and checking the end play
Просмотров 57Месяц назад
I was waiting on my new set of bearings for what felt like forever. But finally, here we are taking care of the crank, and my bolts came in for the oil pump (melling 10295)
Installing my BTR Stage 2 v2 Camshaft
Просмотров 69Месяц назад
This is my favorite part of ls engines. That dang camshaft!! LS3 cam baby
Super quick video of me putting my rods bearing in
Просмотров 59Месяц назад
I am running scat rods, silvolite pistons, and king bearings for my ls3 Silv-O-Lite Hypereutectic Pistons 3530HCA.5MM SCAT ENTERPRISES GM LS 4340 Forged I-Beam Connecting Rods 6.100 2-ICR6100-944 King mb5293si
An easy way to get your rod bolts loose
Просмотров 332Месяц назад
I saw someone describe this technique in a forum and I started played around with it until I figured it out
Assembling the rods and pistons with SRW-012 clips for my ls3
Просмотров 78Месяц назад
Pretty easy after I figured out my technique
I almost destroyed my brand new piston with a flat head screw driver
Просмотров 96Месяц назад
Okay seriously I went around looking at videos of people using a flat head to install the clips and after doing mine I can honestly say don't use a flat head screwdriver to install these clips or similar one just use your fingers fight through the fatigue and you'll be fine
I ordered King main bearing from amazon and they showed up in terrible condition
Просмотров 346Месяц назад
I ordered another set, and it showed up fine I used two different set of the bearings to install all the non-damaged ones. Next time I'll just buy the King HP bearing instead. I still saved money buying two sets vs buying the other options out there, but amazon came through in the end!! These are the King MB5293si bearings The Hp version is king mb5013hp or something like that
Checking my main bearing clearances for my LS3. This Ish is nerve wrecking
Просмотров 185Месяц назад
Bruh no lie I was getting nervous this was the first time I started torquing stuff down for this new engine so sheesh lol Elgin EHC-1007S Main Cap Bolt Set from ebay for $50
This is how I checked the gap for my oil support rings on my LS3
Просмотров 57Месяц назад
This is how I checked the gap for my oil support rings on my LS3
Gapping the second rings for my LS3 pistons
Просмотров 194Месяц назад
Gapping the second rings for my LS3 pistons
I gapped my first EVER piston ring THE TOP RING
Просмотров 273Месяц назад
I gapped my first EVER piston ring THE TOP RING
This is how I cleaned my LS3 engine block!!
Просмотров 475Месяц назад
This is how I cleaned my LS3 engine block!!
C6 Grand Sport vs Alfa Romero twin turbo version (both stock)
Просмотров 282 года назад
C6 Grand Sport vs Alfa Romero twin turbo version (both stock)
My Carvana Experience/ Review W/(Buying a Sports Car)
Просмотров 1,1 тыс.3 года назад
My Carvana Experience/ Review W/(Buying a Sports Car)
2010 C6 Corvette vs a 2020 Charger Scatpack
Просмотров 11 тыс.4 года назад
2010 C6 Corvette vs a 2020 Charger Scatpack
Learning how to use my DSLR with my new Corvette
Просмотров 124 года назад
Learning how to use my DSLR with my new Corvette
Is my Gsxr 1000 still considered FAST?!
Просмотров 194 года назад
Is my Gsxr 1000 still considered FAST?!
Having fun with a Nissan GTR, onboard a GSXR 1000
Просмотров 614 года назад
Having fun with a Nissan GTR, onboard a GSXR 1000
Highway fun with some Liter bikes 😍🚀 Gsxr 1000, Zx10r, Aprilia rsv4
Просмотров 615 лет назад
Highway fun with some Liter bikes 😍🚀 Gsxr 1000, Zx10r, Aprilia rsv4
Suzuki Gsxr 1000 First ride/Reaction In the RAIN!!! 1 hour ride back home
Просмотров 1585 лет назад
Suzuki Gsxr 1000 First ride/Reaction In the RAIN!!! 1 hour ride back home
Amateur Street Racing!!! | DIG NIGHT | Gopro Hero 5
Просмотров 3555 лет назад
Amateur Street Racing!!! | DIG NIGHT | Gopro Hero 5
MUSTANG 5.0 VS HONDA CBR f4I "Highway Fun"
Просмотров 4335 лет назад
MUSTANG 5.0 VS HONDA CBR f4I "Highway Fun"
Must be renting
@@joemauma5035 😂
I looked in my book and the blueprint specs for crank endplay on an LS engine should be between .004 to .008.(four to eight thousandths of an inch) Most guys like to be at the bottom of that spec during assembly because as soon as the engine starts there will be some "break in" wear that happens on the thrust bearing surface area of the main bearing anyway. If you have .002 or .003 during assembly you can count on .004 to .006 after the initial run in. You should be in great shape! I think it's better to build at the lower end of the spec too. That way you don't have to worry about it wearing out of spec during the break in period. Imagine if you started out with .008 on the endplay during assembly. As soon as it starts for the initial run and break in, it would go outside of the .008 clearance almost immediately. You're doing great! Keep up the good work!
Oh really?? That's perfect. Out of all my research I didn't find any information about the initial break in. Let's go!!
Smart move to install the cam and timing components prior to the pistons and rods going in. That way you'll be able to check the clearance between the rod bolts and the cam lobes!
I saw a video of someone doing the cam first a long time ago so I kept that in mind in case I ever built one myself lol
Lookin good!
Thank you 🙌🏾
goddamn is that billet too? i don't think its gonna be a problem tho but dam
Sheesh, I wish haha. It's actually hypereutectic but yeah it tripped me out. In the future, I'm not using a flat head again that's for sure lol
why not use the piston upside down to push em in?
I tried using the piston, but I could not get it to square up consistently the was a bit too much side-to-side play and for my first time I didn't want to continue with it. I had 3 other methods to use, so I didn't stress it. I designed a 3d printed squaring tool for my bore size, I had a roll of painter's tape that fit perfectly, and I bought the tool you see in the video from amazon.
You won’t hurt anything. Ruin coating ? Who said that? lol Maybe you could bend the ring but I don’t see that happening unless you’re a brute. Is doesn’t matter such way you go. I use a dremel and a grinding attachment. I can do just as perfect a job without a ring file tool. My engines have nothing in the catch cans. Cleaning the cylinder walls with trans fluid until you get zero grit will do way more for you than worrying about this. Leaving too much grit even after jet wash will screw up your sealing far worse.
@@Fk8td Thank you for that. I'm still learning of course but most of my knowledge came from reading the forums. Lots of opinions there lol but so far so good 💯
The second ring is not going to be a big issue as long as you've got the gap you need you're good to go. (it doesn't have to be pretty or perfect on the 2nd ring) Your ring gap grinding tool is designed to work by grinding from the outside of the ring (sealing surface) towards the inside of the ring (the part that sits back in the ring land of the piston). You had the direction of rotation correct when you ground this last ring. There is a small issue you need to correct before grinding the top ring gaps though. Instead of grinding one side of the ring at a time, you're supposed to hold pressure on the ring against the two pins and close the ring gap so both sides touch the grinding wheel. I know, this seems like a job for three hands, but you can do it. By holding pressure on the ring against those pins and closing that ring gap to just touch the grinding wheel, you will insure the ring gap will be ground square. (Both sides of the ring will be perfectly flat and true) If you grind one side, then the other, the ring gap will not be square "II", it may look like this "//" or "\l". Again, don't worry about the second rings, they'll be fine, just concentrate on getting the top ring gaps perfect and square. The top ring is where performance is gained or lost. It's a pain and it's frustrating but you can do this. Practice makes perfect.
Thank you so much for these details I really appreciate it!! At the time when I was doing this I was losing my mind because I couldn't get a definite answer to whether my technique was sufficient but I knocked them all out and just went for it. My biggest thing was making sure all the sharp edges were knocked down on the ring lands and there were no tapers in any of the rings. So I'd say it's a success lol
@@Dookamonnnn You're doing great. There's a learning curve to everything, and the more we do the more we learn. You're on your way to building a great engine and your attention to detail like knocking down any sharp edges is proof of that.
Amen.
Congrats. Loved that we could appreciate your cracking buy. Lovely bike.
Scatpack owners getting tossed by Tuned Honda Accords. You really can’t beat PWR. Scatpacks weigh over 4K. Mean while a C6 weighs less than my Camry. (3500 pounds)
Scatpacks just shouldn't be raced in my opinion
The ScatPack should win no problem only if Vette was modified could it win .if downshifting the Scat properly it should do better much better ive beat c7s in 1/8 easily
I just raced another Scat the other day it was a similar result From a 30&50 roll
Lol no it wouldn’t
LS2 car needs a better tuner
Either that or the setup could be bad for roll racing
he don’t know how to drive, also it didn’t seem like he downshifted like u
I think he downshifed he just didnt go low enough maybe
i have ac6 z06 cam and headers in 2nd i kill everyone in roll from 40 hellcat c8 mustang gt all no challenge its funny how scatpack be trying but get destroyed lol
That kia fast af
Not even close!
I thought it would be closer at the time
Make more bike videos!!! Just have to work on the titles to get more featured views. GSXR anything always works. Ride safe nice bike!!!
Man I wanted to see a longer run! We’re you using paddles!
Lol all these goofs bragging about beating a heavy ass 4 door sedan in a 2 door light af vette.......bunch of 🤡
I just realized how light those c6 are shots like 3k Pounds
Homie said boat view😂😂😂😂😂
My c6 when it was stock with the ls2 beat an ls3 vette it depends on your skills
@@seankeys5384 power to weight. If you go to my page, you’ll see I beat two modified cars but lose to a c7
Depends on the driver since the 8speed autos are faster you must shift ur ls2 with the paddles or manual but always be a gear ahead for instance start from 2nd from a stand still in a roll race find ur vette sweet spot but I'm also cammed out and have headers with a borla exhaust on my ls2 convertible and I'm killing everything that comes my way
I have a hci ls2 stock clutch and trans. I ran a scat pack charger and it kept up with me, I guess I need better driving skills 🤣
Yep you definitely need better skills still i mean im blowing folks away ain't no keeping up like I said cams headers and Borla exhaust and I'm looking at a supercharger for her I think I like the c7s too might have to get one but I love love my c6 plus she's paid for so woooo gonna build a drag car out of her in the end I take my vettes seriously dodge have made an ok comeback not much though Chevy power over all from old to new Chevy will always rule
@@rydermob2808 I had traction control turned on. I don’t know if that had anything to do with it. Car dynoed at 489whp. Did a 30 roll from 2nd gear, was shifting at 5500-6000.
@@junior09medina yes never race with traction it slows u down and when u disable it u will feel how liter the take off is compared to traction which makes it stiff
That's not an ls2
Chevy will always be the top dog
#Vettelife just got my grandsport acouole months ago, absolutely love it!
Yess sirr, these things are legendary. Congrats to you 🙌🏾 Never sell it!!
Nice Grandsport! Any mods in this race?
@@Dookamonnnn good honest footage thank you.
can we talk about 0:51 when he tries to kill you? wtf lol
Nice review man! I had a very similar experience with my hellcat
Thank you!! And thank you for watching, you chose a badass car🔥
What was your apr % bro? And if you need music for your videos tap in its good
I got 8% APR and thats a bet!! Thank you
You sure this is a scatpack? I just raced against a 2007 C6 vette and he wasn’t able to keep up with me lol
DooKamonN for sure. Cool stuff
@@Dookamonnnn for daily driving and racing here and there
You'll have more space and better comfort in the Scat since its big but the Vette out performs & handles better than the Scat in every way if you like having passengers n shit then the Scat is better but if you dont care about that then I'd get the vette Overall I think the Vette is a better car Its my choice of the two if you.. plus I like coupes and the scat is too damn heavy
@@just_a5.7 id get a c6
@@DovrDovr-rh7pd I sold my scat haha
Damn son!
My same reaction lol
Dam boyy sick car. Keep pumping out content!!!
Hell yeah Thank you 🙏🏾
Was the stang stock?
The car had an Exhaust but im not sure if it had anything else like a tune of some sort🤷🏾♂️. It didnt pop or shoot flames much so I assumed it had some kind of fuel mapping done for the exhaust
How long have you owned your 2013 gsxr 1000? So far so good?! Good video!
Also got an L2 in this year! This bike is insane and i hope you have a lot of fun with it! Greetings from austria :)
Craziest thing I have done? I have run from cops in a G37 coupe doing close to 200mph and the chase was over within 3 to 5 minutes
Aight, aight, you win lmao... you talked me into getting a 1000 lmao
Hell yeah, Get one!!!
Ok no lie it was honestly pretty sexy when that drop of water dropped down the side of the bike after you washed it
Lmao ain't nothin wrong with that
Hey mate, would you mind if I use it in my compilation? Credited of course
@@Dookamonnnn Thanks a lot mate, yeah ofcourse it will be credited :)
Love the video bro....music is fucking sick!!!
Thank you!! There will be more to come💯
this video is crazy but I enjoyed it!
Yeah it was a pretty crazy night :) definitely wont be the last, Thank you for your support!!
Did you get any runs in?
Lmao that was crazy and what was that flash?
First 😁
I’m pretty sure I saw you with the group of motorcycles it was about 15 in total around there
Og Streaky I think i know the group you are talking about if i remember correctly they peeled off to get gas and i just saw em all at the gas station but i never rode with them tho
Sure was by any chance once you made that left turn in the underpass you gotta me on footage where I got a speeding ticket going 158?
Og Streaky maybe I'll have to go back and check the footage on my PC i know for a fact when i made that left with the cars and bike i didnt see anyone pulled over until i got on the opposite side of the feeder coming back towards the meet
DooKamonN I got on the highway you stayed on feeder ?
Og Streaky I hopped on the highway too just not that first entrance
Yoo don’t stop uploading lol
Og Streaky I gotchu bro just having some set backs but ill be back 💪🤘
#BikeLifeFam