Видео

Thanks bro😊😊

THANK YOU STILL WORKING ♥️ 2024💦

Thank you bro ❤❤

Other than FULLY turning the bottom screw, which does nothing but either hug or push the cover away from the body, here are some instructions I hope you find helpful. Location of attachment points: BOTTOM: Measuring 1 centimeter from the bottom corner along the bottom edge on each side, you will find one plastic hook attached to the back case clipping onto the internal plastic frame. A very thin flat blade screwdriver should release it. Otherwise no other hooks or snags along the bottom. SIDES: This is where the real fun begins. Strangely the back cover has inset attachment points, instead of between the case edge and the screen. 4 U-hook anchor points located at: 1). Horizontally: 1.8cm in from the outside edge, Vertically: 7.8cm up from the bottom outside edge 2). Horizontally: 1.8cm in from the outside edge, Vertically: 14.4cm up from the bottom outside edge 3). Horizontally: 1.8cm in from the outside edge, Vertically: 19.5cm up from the bottom outside edge 4). Horizontally: 1.8cm in from the outside edge, Vertically: 28.8cm up from the bottom outside edge These are the MOST difficult to disengage. Simply running a guitar pick or screwdriver or slidey bar between the edge and screen doesn’t work. In the past, I’ve been too gentle on the edges and like a surgeon separated the screen glass from the screen digitizer ruining the entire PC. My suggestion is to stick a screwdriver or a block of something inside the stand hole, between the cover and the body to keep up the pressure on the back case as you go along. Since there is nothing to release along the visual edges, you have to pull the bottom, slide along the side, relax, pull, slide, relax, technique along the bottom and edges until something eventually gives. Hopefully, it won’t be your patience. Fingernails are sometimes the best weapon. TOP: There are 8 cover plastic nibs spaced evenly along the top edge, 4 to the left and right of the camera slide switch. You might try inserting a very thin guitar pick along that edge. I didn’t because I was too afraid of killing another PC again. Getting the plastic cover away may be tricky. There are no delicate cables to worry about. You might get a string of rubber coming out from between the side edges but you can lightly glue them back, I used a slight brush of Elmers rubber glue. This is the worst case I’ve ever seen for repairs. The attachment points are way too hard and certainly not made to easily open. I would never suggest this PC because the next repair guy might have to buy you a new one out of his own pocket. Good luck friend, you're going to need it. 😄😉

🎉🎉🎉🎉🎉

thank u sooo sooo much

U deserve a million views ❤

Hello, mere 24 inch LG monitor pe ek kapde ki wave ka jaise adhe screen pe wave bani hui hai. It is not visible when the monitor is on and works okay. What could be the problem?

Thank you brother 🤍💙🖤

Worked for me tks ..dude❤

THANKS BRO

Thanks it works for me

Tussi great ho😎

Thanks bro apki video se dawnload huya h bss thanku

Thanks🥹

Thanks master

Thank you so much Best Buy said the hard drive can not be replaced or removed by hand because it was soldered into place. It must be shipped off bs.

hola, una pregunta, para actualizar la bios de esa placa madre, se necesita el adaptador de 1.8V para la programadora? desde ya te agradezco

kya speed hota hai .. pci x1 me or .. kya .. .windows ho jaata hai ..

sir .... pci x1 me speed kya aata hai or .. sath aap motherbord me ..... windows is m.2nvme se .. inscroll ho .ja raha hai ..

If we dont have internet how can we open google

Wife adepter connect ho gya

thank you so much bro 4 month se pareshan the... Ab thk hoga tumhara video ko follow kiye to.... ❤❤❤❤❤❤❤❤❤❤❤

Thanks bro, it's worked..

Thank you so much bro,,,,lot of videos watched but the problem was not solved, finally worked on it....again thank you so much bro

What if you dont have chrome

GRACIAS HERMANO

Stop, Stop, Stop!!! WIE bekommt man die Abdeckungen weg, damit man die 4 Schrauben ganz am Anfang lösen kann? Stop, stop, stop!!! HOW do you get the covers off so that you can loosen the 4 screws at the very beginning?

Bro ,, colour problem in my laptop 😢,,what to do?

Olá 👋👋👋 meu setup em Drives não aparece o SSD... 😢 O quê fazer?

Thanks bro. Its work

İ ve been lookongvforvthis video thanks, but what is the melting metal you used exactly?

Can you tell me how to boot it on nvme ssd and how to install that original windows in nvme ssd Make a video on that

Bro

Bro what was problem

Nicee....thanks ..suksesfull..🎉

Thank you so much, it worked perfectly❤

Brother, you deserve a million subscribers Thank you, thank you from the heart ♡♡♡♡♡♡♡

U ARE A LEGEND ❤

Thanku broo 100%working

I try this trick 100% working thanks for this information thanks 🙏🙏🙏🙏🙏🙏🙏🙏👍👍👍👍👍👍👍👍👍👍👍👍

😘🥺

Thanks mate! this is great

Read and write speed

You are a real retardant. You don't talk or explain, you just dump threw the fucking hoops, like we can reread the damn screen you fucktard.

❤ Thanks a lot It's worked

Bhai tq ❤❤

Tq mawa

thank you very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very very much sir😊😊

Woww it solved my problem