Видео

shopee.com.my/MOTORLAND~Brass-Adapter-Nozzle-Brass-For-Karcher-High-Quality-Spray-Rod-Replacement-i.171694043.20382556728. Got it online from Malaysia

maybe the code key box is faulty

yes. lost key programme@@raziackzing

Hi I use CRC808 Spray. i avoid grease as it can pop out the dust cap if too much and start collecting dust. grease are like magnet to dust and it dries into a hard paste.

ini Wired connection. ye ini bukan trackmix. Ini boleh manual optical zoom.

tak ade local external recording. Semua atas SD dan Reolink cloud.

saya tak record 24/7, walaupun boleh. record bila ada motion detection.

boleh dengar sikit..macam lebah terbang. i masih boleh terima as long this punya tracking is accurate tak macam camera 5Mpixel. lepas tracking dia punya return to home sesat. camera ini tak sesat.

@@raziackzing Terima kasih bro. Saya bercadang nak letak model ni dekat luar rumah. Buat masa ni pakai Reolink E1 Pro je hahah (model 823A tak keluar lagi masa tu)

@Radhwan saya pun sama pakai e1 outdoor dengan tracking yang tak tepat. Banyak kali I complain kat reolink yang 823A kenapa tak ade ship model ini untuk malaysia. Singapore dan Thailand ade. Nak ship ke Malaysia tak bole.. lepas tu I mintak member beli dari Singapore. Lepas 2 bulan dah malaysia pun ade. Adui.

@@raziackzing Biasa la Malaysia ni slow hahah. Reolink Video Doorbell pun tak sampai2 lagi 😅

@@MohdRadhwan yelah

this camera works well.

Not easy.. best bet online alfa forums

@@raziackzing which way does that notch come against the sheet metal corner that is in the frame?

i use Cat6 cable from Prolink. This camera is connected over powerline device that can only support 200Mbps.

@@raziackzing do you have nvr too if yes what model number of the nvr?

@@DimplesDon9 without nvr

@@raziackzing one more thing. It followed smoothly if it's ok to share the firmware version on the camera? Thanks again!

Firmware version : v3.0.0.653_21101511_v1.0.0.30

en.alfaromeo-club.com/manuals.php?ddlb_category=11&ddlb_model=3

@@raziackzing i want to know where the relay exists

@@abdelwahedromadi867 I'm not sure for 147 as 147 have newer engine and layout. Need to check service manual and try to identify.

Also if possible you might do relay test from your tester and if the relay click then that's your relay. These is depending on what diagnostic software you have. Not all kind of relay can do this test.

Also try to hear if the fuel pump is priming from the back when you on the car 1st time in that day.. just to make sure fuel is pumped into engine.

ini national

Thanks..

Harap ia membantu.

Tq

@@raziackzing vii sruh reply 🤭👏

@@abangadmin253 ooooo hahahaha

it will not slide all the way in is because grease will seal the air pockets in. with force we can remove these air pockets. yup i could have reduce the grease and re-grease every 2 oil change. Thanks on the feed back. the grease tube also full of air.. the large grease tube nampak je gempak..

is it the cone? there is top cone and there is bottom cone. To remove cone you need to remove the whole motor and its blade. Loosen the screw and slide it down.

tukar bearing kipas ceiling

Boleh tukar. Sebab I check I punya masih ok.. kalau ade koyak atau leaking I mesti tukar. Kalau boleh tukar lagi bagus. Zaman Covid banyak kedai tutup masa itu.

You 're Welcome

TQ 👍

@@raziackzing welcome

Tq

Yes you need place and tools to work on it. Do check on how I worked on the front brakes as well. All this is DIY. Not workshop.

No studs on motor

@@raziackzing what's the correct answer

@@faridahzulaikha7459 there are no studs on the motor.

It is actually called "F-MY153" not "FMY-153"

@@ceilingfanmaster9569 R EXPENSIVE YOU MEAN THAN 2004 VERSION

Maybe you can try Contact cleaner.. spray from the bottom of the key hole where the wire goes in and open close the key repeatedly. Need to open the 2 side cover and one top tank cover.

Thank you very much. It works like a charm

Ultra rare

It's from 2003.

@@vigneshwaranbanknotes7405 yes

@@vigneshwaranbanknotes7405 it very expensive RM125 in 2003 until panasonic release due to national expensive so 2004 name National to Panasonic :(

yes bro, how are you keeping. maybe one day i'll share my 146 engine rebuilt pictures in my porch. Lucky to have a good support from the IA community and some friends.

@@raziackzing lidat la.. and getting older... u stay near yellowtaxi, remember him?

Yes remember, near only. walking distance now. i think its him la. after so long no see him. still with yellow coupe.

Yes this is long lasting fan and easy to fix.

@@raziackzing yeah

Ya ikr

@@raziackzing in 2004 it change named National to Panasonic

Yeah, Uma/RCB products waste alot of money only. disturbance in my cash flow. HAHAHA.

Its due to weak contact within the fuse holder and fuse itself.

Sorry this I'm not very sure. Maybe the heat is actually normal or if its too hot then the unit you got could be also defective.

tak Naik apa apa kat display. parah dah tu. Dah Dua kali i tuka pun, sama. I check semua wiring dari charging ke battery baru pun sama. Dua dua meter i ada masalah sama. UMA/RCB product quality teruk termasuk ECU EX5 diaorang. boleh tina tiba rosak. Nasib baik dekat rumah dah. Kalau ada masa saya akan buat video atas component i guna atas ex5 dan benda yang rosak .

Glad it helped. as fuse gets old the oxidization will build up

Check all the fuse in engine bay. Clean it with contact cleaner on the fuse and the socket. And put it back.. if it's blown. Replace it.. boxer wiring is different than my 146ti.

Do ecu diagnostic and see for any error and check on the sensor involved or component.

My objective here is to remove all old oil in the lifters.

@@raziackzing i am locking for a solucion for my alfa. it may be the same problem as yours. cen you just tell me if the engine made some weard noises? like nocking?

@@tarikGP0 if its there all the time on idle it could be variator.. sounds like diesel engine.

@@raziackzing I dont know. Not shure about the diesel sound. But there is an easy test that I cen be shure about. Run it on idle for 10 minutes, if the sounds stop it is the variator. If not then the lifters. Its just so that the oil gets hot enough (operating temperature) to flow freely to it.

@@tarikGP0 if its your hydraulic lifters noisy, either its your oil too thin or your oil passage to lifters is clogged.