Видео

A gdzie czyszczenie i smarowanie bendixa?

What’s the force to tighten the nuts at the end please ?

No arson?😢

Esa manguera que esta en medio de las dos tapas negras. A donde va conectada?

Easier yet to set the wheel hub on a cheap hotplate. Also throw the bearings in the freezer. They literally drop right in.... And dont forget to put the spacer in before the second bearing!!!! I have seen that mistake before..

What method do you use to ensure the rear wheel is aligned/adjusted properly? Just eyeball it? I'm planning on tackling this soon myself and that's the only part that worries me.

The grease you drop in the outer dustcaps is that neccesary ? It seems to me that this adds no value , on the contrairy its holding the sand that enters ...please correct me if i'm wrong. My son followed your instructions by a previous replacement of his backwheel bearings on his 250 YZ, now i'm replacing his chain and sprockets and found the sand enriched grease and my mechanicsmind does'nt understand the logics in putting grease on the outside off a closed wheelbearing Thankx for the movie!

What music is this😂

What is the Black button you Can press or pull for?

does the oil have to be out of the bike to replace this?

Very good job

The head bolts look stretched

Good working sir 😊😊

thanks for the video. in the video it appeared that you cleaned the calipers with some kind of solvent before installing the new seals. was that acetone? fuel gas? what was it? thanks in advance.

Thanks for the very nice and detailed video👍

cf moto 625 cc atv Does it fit?

Und - die drei kleinen Wellen des Planetengetriebes bekommen kein Fett? Die Hohlwelle vorn die Ausrückt hätte dich bestimmt auch über frisches Fett gefreut. Sonst ganz ok.

Hello, dear friend. I put one bearing completely inside the seat, but the original spacer is about 0.5 mm bigger and the second bearing does not fit completely inside the seat. Does this not cause a problem? If I hit the second bearing more, they become completely stiff and it is no longer possible to rotate the bearings with a finger. Thanks.

Thx

I lost my C clip or bearing retainer do I need it?

What was the 0.00 supposed to be? 0.10? Same as bottom one?

How do you adjust the floats if they didn’t go back to 13mm?

what year is your bike? I have a 2018. I assume Yamaha has not changed the design of the counter shaft over the years. I think Yamaha prob use the same design for the 2 stroke and 4 stroke models. Do you recommend buying generic brand like All Balls seal kit or stick to with OEM parts?

What is the white lube you are using ?

part number for that please

Thank you! Awesome video

nice

Is there any change in performance of using the more free flowing piston from Zeta?

How do u know how much to screw that last blue screw in the one with 1,2,3,4

Thats not a DT125!

What did you use to clean the outside?

Dude that music sucks and ruined the whole video

What can I do if I don’t have a vice

Was your raptor backfiring through the carbs on a cold start?

Hi. An incorrect clearance of the valve (in particular the intake one) and/or much carbon deposits inside the valve adjusting room...can cause the problem that the engine does not keep the idle even if the bolt of regulation of the idle is in the position of maximum ? I have this problem with a 2004 Kymco KXR 250 sport: the carburetor is perfectly clean, there are no places where air can enter supply circuit, the spark plug is new, air filter well cleaned and so on. The carburetion setting is a little bit rich...but i don't think that is the problem. I have seen that the spark plug becomes dirty with carbon deposits very quickly. Thank you very much in advance.

Great work! Where can I buy the piston rings for raptor 660?

good video but i wonder what the engineers were thinking about when they decided to bolt the cases together with philips bolts

Great video. Felt like I was on hold though with the music haha

8:05 is magic? F.ck.... Very big problem for me and in video none. LoL.... Thx

Hello you would can to say for me a swimmer level stopping the needle which one nútban is?

Good job 👍👍👍

Music is annoying

Why does a motor cough out the Intank ? Can it also be a valve ? I was thinking or maybe spring is to week and valve ain’t closing fast enough?

This is a stupid video

No need to remove sparkplug?

Great video 👌👌👌👍👍

Is there another way to confirm this with motor in?

So the leaking valve caused backfire?

I have a 660 I had built tuned ran great. Had the case crack a tiny bit got it all redone nee again. At a shop now it backfires alot on deacceleration. When let off the throttle when moving What causes this ?also has alot of carbon build up on the grab bar from muffler

I looked up gear change unit and nothing came up is there another name for it