![KRS Corporation](/img/default-banner.jpg)
- Видео 95
- Просмотров 148 395
KRS Corporation
США
Добавлен 4 окт 2011
Welcome to our video site
This site has videos of products, projects and sometimes just stuff I try.
This site has videos of products, projects and sometimes just stuff I try.
Using our Glenbrook JewelBox-70T X-ray machine to look inside a USB cable with damaging it.
Looking inside a new cable to see how it was soldered up, does it have shielding and what size are the wires.
This X-Ray has a tilt ability to the object we are investigating. with X Y and Z movements we also have Tilt and Slant. We can rotate an item to see what it looks like from an angle to see around corners inside or around other objects. This machine is the JewelBox-70T.
We look inside the cable without destroying it.
We use the x-ray when investigating PCB's or other things that we do not want to destroy but understand what is going on under cover.
This X-Ray has a tilt ability to the object we are investigating. with X Y and Z movements we also have Tilt and Slant. We can rotate an item to see what it looks like from an angle to see around corners inside or around other objects. This machine is the JewelBox-70T.
We look inside the cable without destroying it.
We use the x-ray when investigating PCB's or other things that we do not want to destroy but understand what is going on under cover.
Просмотров: 35
Видео
Whale Watching in Long Beach CA
Просмотров 310Год назад
Whale and Dolphin watching in Long Beach on Aug, 12, 2023. We got to see a couple Blue whales and a lot of Dolphins. The video is shot on a boat from the tour company Harbor Breeze Tours 18 miles out into the ocean. This 3 hour tour had I would guess 125 people onboard. This was shot with an iPhone 12 on the open water. So ups and downs with the waves.
1992 diesel fuel filter lower drain cap. 7.3L idi - Non-Turbo
Просмотров 126Год назад
Original Fuel Filter lower cap/drain close up. What is it and how does it work. This is what the lower drain on a fuel filter for a 1992 era diesel 7.3L non-turbo looks like. How it works and disassembly. I cleaned it with isopropyl alcohol to cut all the dirt and grime in it so it could be reassembled and used again.
Easy Open Demo
Просмотров 35Год назад
This is a simple demonstration of our new product, the easy open. The easy open allows you to easily grab a 3 inch paint cap on top of the paint bucket. The threads when covered with paint from pouring out acts like glue, and causes the cap to be stuck down, and if you don't have a good tool, you'll end up, destroying the cap and ruining the threat.
Hot Foil Stamp Machine
Просмотров 91Год назад
New to us Franklin 1020 Hot stamp machine Foil and rubber silicone die. This video is about setting up and using our new machine for the first time. It sit for 525°F and takes about 20 minutes to get warm. Once ready, it will print in less than two seconds.
Setting a mold in a TOYO Si-300-6s Injection Molding Machine
Просмотров 46 тыс.Год назад
Setting a mold in an injection molding machine after a nozzle alignment. We use a gantry lift to get it into the machine. Mold weight is estimated 650lbs. This video is as much for me as anyone else. Most everyone watching this probably has a lot more experience than I do. This is not a guide for how you should set a mold, this is a guide for me.
Toyo Si 300 6s Nozzle Center Alignment
Просмотров 663Год назад
Barrel and nozzle alignment on a TOYO Is-300-6s. Our new machine, after the install had the barrel not quite centered for the front center. The molds do not have any give for alignment. This is how we did the centering of the barrel and tip. The tip was dented when I thought the installation technician had already done this, I should not have assumed anything. We were off about 5mm when I state...
Making quick water lines for mold cooling
Просмотров 61Год назад
Making quick water lines for mold cooling
EH Auto Adjust Error, Toyo TM200H
Просмотров 306Год назад
EH Auto adjust error on a TOYO TM-200 H series machine. PLCS-9 OS. The video is as much for me as it is anyone else, I could not find any information on the error let alone how to recover from it. I hope this helps you, I am not an expert, but a complete novice. These machines are very dangerous, use extreme caution and none of this information is assumed to be correct. Use this information at ...
Tesla ride in the tunnels of Las Vegas.
Просмотров 272 года назад
Tesla ride in the tunnels of Las Vegas.
Config Mode: TDS Keypad, how to enter config mode
Просмотров 693 года назад
Config Mode: TDS Keypad, how to enter config mode
DCS 1800z Caping Station Exchange, mistake and all
Просмотров 2925 лет назад
DCS 1800z Caping Station Exchange, mistake and all
Thank you! I've been looking for settings for cutting leather with a fiber laser everywhere. Your settings worked perfectly for me, and I got some cool fire myself.
Just got the trip yesterday and ran across this video searching for clues. Like yours, mine was stored for 5 years in an RV storage garage, but has worked fine for last 4 years - hoping it's this issue! Thanks for posting this - I'll clean it up with some 99% Isopropyl alcohol and see what happens.
Just in at 5 minutes. Did you loosen the rod on the other side too, no rotation, just loosen so it can float? Off topic, but I gotta ask, Do you have a brother that drives a truck?
yes, it is very important to run the nozzle all the way back and forward each time you make a change and tighten them. Do not move it with anything lose.
Dirt not moisture..may have bearing going bad
Yes, but they had moisture on the encoders, it was both. This was cleaned and put back together at least 7-8 years ago and it has never had an issue so the repair seems to have worked.
Thanks for the laser settings. What are the hash settings? I cant seem to get clean text repeatedly. Thanks in advance
I watched your RUclips channel Very nice videos on your channel, I have watched all your uploaded videos and noticed all the videos are nice. But there is a small problem. Your video uploads have to do some work like (SEO) and help in getting future video views. You are working so hard just to get views, now if the views don't come then your hard work is useless. All video SEO does, you will see that your video views will come. I can help if you want. Thank you, have a nice day
Thanks for the videos you make about injection moulding. I came here to tell you that you wrongly select "this video is for kids". Doing these will diminuis interaction and forbid to comment, you can still change this if you want. regards!
Thank you, I updated my videos.
HELLO IS THAT I CAN PLACE AN ENCODER IN A MOTOR STEOER AND HOW I CAN CABLE IT
How avoid the fire?
You can increase the speed slightly and do multiple passes instead.
Why is it black? Are u using a laser marking spray? I want to be able to etch or engrave the PC in clear not black. Any help is appreciated thanks
Hay guys, could this laser be used to recreate famous watch dials, like Rolex, and IWC. I am a watch dial refinished. I use and ink pad set up. I need something that will create the copper dies.
0:26 You were going plaid before Tesla made it cool!
It is possible to get touch text on ID cards ?
By touch text do you mean, raised lettering or a raised logo off the surface? If so then doing UV printing would be a much better choice. With some types of UV printing you can do complete 3-D text and raised graphics. A fiber laser is etching into the material but not at a depth where you can feel it. If you use a fiber on softer metals like brass, aluminum or such you can etch into them to make textures but it takes a lot of power and time to do it.
It is fiber laser or co2?
Fiber laser
@@KRSbumpbars and it is 30 watt? Rycus? You can make a plate for any kind of material (i mean like what in exposure, they have screen line to adjust the ink fluid)? I interesting to buy laser. Thanks
@@mendy770 this is a 30w Mopa fiber laser. You can loop the program for more depth, I always go light on passes. It take trial and testing to get it right for your inks.
What u have did to overcome the bad smell of burning leather?
Really good results! I'm having trouble getting a decent result... for some reason even though most of the design gets engraved correctly, part of it passes through the top layer of the plastic, and engraves on the back layer! Any idea on fixing this issue? thanks!
Not sure why you would have part of the design correct and part out, but it might be something out of alignment or you are writing larger than the lens will support. It may take breaking the text into two areas and doing two jobs?
@@KRSbumpbars hey! Thanks for the reply, I think you didn't understand me correctly, the design is aligned correctly. And its just a small test. But the laser seems to just pass through the polycarbonate at some points, and burn the rear side (down, facing the table) instead of burning the top side (facing the laser) 🤔
No se ve el resultado :o
what did you spray on the shirt? it's wet?
Distilled water for this ink. Spray very wet but not dripping. DCS ir6 ink
that white ink looks good my look gray,why is that?
We do two passes of the print over the same spot. You can do white with two passes then the color on top also.
you don't change the settings to do dark and lite shirt
What size lense are you using please?
This is a 30w fiber, i do not remember the power setting but it was low. Leather burns fast .
Can I get your What's App number for more information
Do not have a What's App number. What question do you have?
Wow very wonderful
Hi Can you help me wiring to rotary :)
You should contact the ones who sold it to you both the rotary and the fiber to ask for instructions. There are a lot of different control boards some support rotary sone do not. I am doubtful that I could really help much with out direct input from the sellers.
@@KRSbumpbars Thank you. I can do it now. :)
where can I buy those plates?
Ink Cups Now is my supplier
How did you pre treat the garment?
Spray bottle with Distilled water. This is what is required for our ink from DCS. We use ir6 inks
شكرا علي ترجمة هذا الفديو ويا حبذا يترجم من مثل هذا الفديو
how do you keep the tsirts that tight while its in the printer. it should be a flat surface right ? Please help. thank you
There is a jig that holds the shirts. It is a simple flat platform that the shirt hangs down the sides. Then they tuck into the sides, held by a rubber wedge. Simple and it stays in place.
@@KRSbumpbars can you please share a picture or the material used for the jigs it'll help me understand better. Thank you so much for the prompt reply
@@abdullahmojawala7021 www.directcolorsystems.com/applications-2/dtg-t-shirt-printing/ This has a couple videos of doing shirts. This is a company video, I am a user not related to the company.
Hi KRS. I followed your parameters and they made a dramatic change on the quality of the print. I have to accept what the quality is very good. Is it possible to get your opinion on how to improve my print? The result I get is what is a bit translucent. On a logo wit a solid thin line the print doesn’t seem solid.
I can try, not sure I can provide much help. It just take practice and small adjustments to get what you want.
@@KRSbumpbars whats the maximum resolution dpi
@@goldcoasttime the resolution is very high, it is vector graphics so the dot size is more related to the ink and pad quality. I would think it is much better than 300 dpi.
If your using Ezcad you can adjust your visible laser to match your actual cutting edge. F3 then other tab, then outline button. It will now allow you to move the visible path to match actual cut path.
My servo moter encoder prom same part no avbl in my city encoder part 3409/549 code I change this parts then more difrt part set
where to buy this ink. Thanks
The manufacturer sells the ink. Direct Color Systems; this is the Flexible ink.
Use alcohol to clean it
I thought uv printers penetrate fabrics and they only made to print on wood, metal, canvas, but not garment.
This one with the Flexible ink works great on about everything. Sometimes you have to pre-treat a material to get the ink to hold but overall they are great.
@@KRSbumpbars do all uv printers use the type of ink you're suggesting?
@@KRSbumpbars what type of pre-treatment are you using for the uv ink to hold on the shirt ?
I made this and other shirts about 7 months ago. Then have been through many washes and are holding up really good.
what is the duration of washing of the tshirt? after how many wash the print goes away?
I made this and others about 7 months ago. They have been worn and wash many times. They still look very good and I have not been kind to them, I wear them everywhere all the time.
Put masking tape over the leather before cut, this avoids the smoke tarnish the leather
What flavor machine ?? Nice lettering !
Wisley MOPA 30w, thanks
And now you found the problem exactly the yen And what is your solution? I think the shaper in the engine
My servo moter E6 probm
My servo moter E6 probm
Error codes, at least you get an error. You will need to contact your machine manufacture or go to their website to see if you can get an error code list to see what it might be.
Which website
My servo moter E6 probm
Which is used in uv printing for t shirts printing?
We print uni-directional on shirts instead of bi-directional. This is set in the print Queue section of the post processor. We found that the printer is not perfect on shirts when going both directions. Let me know if you have a different question.
Ahmad: The Heat press is absolutely necessary, it will not stay without it and you have to pre-press it to get the fibers down before printing. My press (Amazon $175) is not a good one and I am going to have to get a much better one. The problem is not a good consistent uniform heat. Everyone I have spoken with says a swing-arm ($ 1500.00 + ) is the only type that will work correctly. DCS printers require the pre-treatment to be Distilled water while other printers use a chemical pre-treatment. Settings: I will have to check, our DCS printer has queues you use for shirt types and colors. Poly, Cotton, Dark, Light, Poly-Blend all have different queues and settings.
Beautiful work. What model is that? Cobra? I'll have mine up and running in the next month. Can't wait.
which software do you use to create the g code files?
I used the Vectric program: Aspire. This is a gadget add in, it may work in V-Carve pro too but I do not know. Real easy to use just define the size and teeth and it makes the gear. I will see if I can make a screen recording of how to do it, but it is simple.
Eaglein80 thanks.i will try it.i Made a drag knife but i have no idea how to make These Files :-)
One important step which was not mentioned: you must hit the 2&3 buttons WITHIN 3 SECONDS of plugging the keypad into your USB port.
I never thought about a pinch joint like that.
What are you building with all those plates?
Cutting at about 50 inch/Minute 15,000 RPM
isso é pedra?ela grava em granito?
Did you ever sell that machine? I saw it on cammaster's site.