Видео

3D printing tests your patience. Besides filament clogs, I also have serial failures (at 10 hours into 14 hour print) which is probably because AUTO/AUTO picks 250000 baud wow). It takes a lot of learning and experience to get good results consistently. Thank you, this video was very helpful.

grazy

G’day Anthony. That’s one unique clock mate. Great idea 💡. Cheers Aaron 🍻

Nice project but, audio is very low and there is no link to the code.

Awesome project, mate 😊

Hey Anthony. That was a very satisfying video mate. I really enjoyed it. Such an overlooked item in everyday use. Cheers, Aaron.

I like to camp in detents!

Much like the detents, this video's gone underappreciated too!

Hmm im stuck with the ball bearing not coming off the axle. Guess it will come down to brute force

Good job mate !!!

So the airflow does get affected by air leaking through the print layers, it'd always been discussed that 3D prints couldn't be used as vessels to hold liquids and experience with a Stratasys support bath suggests as much as well. It'd be interesting to see if a version of this sprayed with clear coat or event just a flat colour helps to seal the microgaps in the layers and the airflow to/from the pump is improved.

Awesome video! With love from a fellow ZB owner 👌💪👍✌

Thanks for showing your excellent Fairlane looks & sounds amazing

THANK YOU SO MUCH !!!!!!!!

Can we reuse after sharpening?

Where did you find the axel?

Great stuff! Really highlights the power in the maker community to develop custom solutions for low cost. Your students will benefit greatly from this. Only a little warping on the corner of a model near the edge of the bed is a great result, looks like the Ender 3 is working well.

Thank you very much for your information

Excuse me,one question? do you think if be able to program a key fob with it? 2012 Lexus ct200h

Great explanation! Just watched the vid and ordered the front axle, seems easy enough to replace. For me, a wheel fell off because the axle broke. Very clear now how to replace it, thanks a bunch!

The cat sits in there because mice have probably moved in. Nice to see the engine bay of a TR7 again.

Ha, I called it early on. Of course, I had an analog computer lab in college, and we learned real quick to test each cable as we added it to the programming. I have a different version of that power supply. It has a knobs for both voltage and current limit adjustment. I think that arrangement is less confusing. Pro tip: make yourself some buss bars out of 12 ga solid wire with spade lugs shaped to fit rightbon the binding posts for serial and parallel modes. You seriously don't want to make a mistake there. Both serial and parallel modes work well.

Hi, yeah, been there, done that. As I couldn't see the labels on the various buttons, my first thought was had you enabled the outputs. Some power supplies have an enable button, so you can set everything up prior to allowing the output to be connected to your circuit. I also considered sense circuits not connected or enabled. It's odd how we ignore something that should be obvious and looks us right in the face. I'm glad you found the problem, but you lost your hair in the process !! Lol.

Good quality out of the first print, a bit of fine tuning from there and it'll be mega. Creality are amazing value for money even more-so now than they were five or six years ago when I bought my Ender 5. Their entire product line-up now makes it amazing value for money for people getting started without the finances for an Artec scanner or Trotec laser cutter. I'm eyeing off a K1 to eventually replace my aging Ender 5, but I just need some space to put it!

Nice pickup, what a bargain!! Thanks for sharing the setup and first print with us!!

"Bowden gap" is literally the oldest Ender-3 problem. At the very minimum you should not have tightened the nozzle before putting the bowden tube in, you should back off the nozzle 1 full turn, insert the bowden tube, then finish tightening the nozzle, so it will squeeze against the bowden tube, not permanent because the coupling will eventually allow the tube to move up and create the gap again. For a permanent solution you should do Luke Hatfield's hotend fix. Also, if you print a knob for your extruder and instead of trying to push the filament in, you put it in position and turn the knob, it will go through that first coupling without catching on the sides.

Can I buy a light kit from you ?

Great ❤❤

Pls how can i take it -from where ❤

Set it for 16 pin and see if it works. It does alot! It checks for codes in modules. Codes in modules can be caused by corrosion on fuses. Erase the code in a module and drive it and see if it comes back.

thank you! ive been wondering if i could add cruise control to my is200 so its nice to see how you've done it

Did cleaning these filters fix the problem? We have an S5 Max with the same continuous error.

great review.Tough and great for the kids

The 300, straight 6 or 4.9ltr was the best of Fords 6 cylinder engine line

Spray the entire bottom side of your car with WD-40//some kind of rust Keep the bottom of your car oily

What a fun little project! Well done!

Good luck with the Sniper. We are on the 3 Rd one in 3,000 miles.

Looks lije its coming along nicely Ant.👍🏻

Very well sir

Amazing this lecture sir

I have a 1996 Lincoln Mark VIII , I dont want to blow up my car , so I won't attempt to stall Jack , Also I'm not taking out my classic radio , all I need is something to play musuc from my I-phone , to my car speakers , and mount it under the dash , , What is the name and model of the product you are showing and where can it be purchased ?

Very important tips Anthony. Well done 👍

Hello, i got many Kyosho Pureten, and it's so greats cars. Sorry for my bad english 😅✌️🤘

Thanks for the drive ,I enjoyed being passenger . I do have question …..we’re the 6 cylinder ZB autos fitted with a C4 ( cruisomatic ) or a BW35 , or could were both trans available with the 3.6 ? Are you running a 250 with a BW 35 ( it looks like it to me with the selector quadrant ) thanks you may help me solve a mystery at least to me .

Hey did you ever make a video installing the snipper system into the car?

Nice Vid Ant! Still giving out helpful info to the masses. 😁

Mind you this car was sort of rushed to market so Tesla could grow the company revenue to come out with the cheaper sedan and SUV (model 3 and Y). The updated S and X are really great products but the new Model 3 that just released is absolutely a great deal, and I expect the upcoming Model Y update to be released soon and that'll be the best deal on the market

I wanted to see how the screw fit!

Huge like and sub!!

Dude I’m In same boat bought one of these I’m A crawler really but keep seeing all kinds of dudes with arrmas loving them And their toughness!!! Glad to see your lasting so well after years of this abuse!! They are hard. It to abuse!!!