Видео

I gotta try this

Thanks for the video, music really makes it hard to hear you. Do you have any other snack recipes for Carnivore? Thanks so much

Thanks for the video. Whats the best way to store this and how long will it store for?

This is absolutely so smart! I'm going to try it. I'm celiac and have to be very careful of additives.

Remember to use the smallest mixing bowl possible for the best results…

Giraffe fed beef works best

Thank you so much ❤

What’s the main breaker switch for?

Looks really good. I can't wait to try it.

Thank you, love how you can make this withoutout extra equipment!

A pizza cutter would work great!

Ale chłopie… coś Ty mierzył. Kąt noża zmierz a nie noża z chwytem 🤦‍♂️

are you useing 1 or 2 pounds of ground beef ?????????

Good question .

I own two of these sharpening systems Ive tried washers of brass stainless steel and cheap washers all miked to the same thickness. Nothing has ever came close to being the same measurement when flipped. Ever.

First time I’ve ever seen a westinghouse generator run! I didn’t think it was possible. I’ve received three units in a row from Amazon that were DOA. Wouldn’t recommend this brand to worst enemy.

Wrong technique to measure.. you should only measure blade angle.

Thank you so much!

Cost effective, you figure $0.80 cents of power, 1lb meat $6-7 dollars 2-3 hours of time, compared to a 1lb bag of jerky at $25-28 dollars.

Can it be done in a regular oven? I don't have either a dehydrator or a convection oven.

The grip system on the RUIXIN PRO RX-800 is a bad joke. They fixed it with the RUIXIN PRO RX-900

Does this work on powder coated pontoon?

Fun fact, the pull doesn't work without a battery charge. Dumbest design.

Nice video. Not a bunch of extra. The Parchment paper rolling and cooking part was what I wanted to see so I can get ir right the 1st time. Thank you.

I have the same exact generator. Usually always run on propane. Never had a problem till recently. Last time I pulled it out to run for a bit, would not start. Used the electric start till the battery started running down. Tried the pull start, still nothing. But then tried the electric and it sputtered a little, but that was it. I could smell a little propane and I started to wonder if the regulator on the propane tank is clogged or something. Anybody have an ideas? I'm tempted to try gas, but if it does not start, then I might have to drain the gas out. I just like using the propane, not as messy.

Mixing this with dried fruit is amazing

Looks great

I sure would like the ingredients you use. Thank you!

Super easy. Thank you!

Thanks for your video... I am going to try this.

Very nice recipe... can't wait to try. I did chicken breasts in the blender then cooked the same way from another video (she called them chips), & they were amazing!

How long should this last without refrigeration?

Just sending it back... other issues plus this one

Made in china scrap...

Is your table level? Maybe the floor isn’t level?

You may need to change the title of this video. As it appears you are replacing a Whirlpool wall oven and not a KitchenAid oven.

All this video proves to me is you buy shit you end up with shit!!

Next time try using some foil layers or some sticky tabs.

Looks easy enough

what app are you using for this ?

Thanks for the demo (and explaining what Barry Morphew did after murdering his wife Suzanne..)

I saw an Amazon reviewer complaining about the angle difference. I have not checked this yet myself.

What did you use?

I'm really pleased with this! It works like a charm ruclips.net/user/postUgkxDcr-y2Pf6xdnrFHrSP7dl9kpKaCozcSQ Takes less time than my old electric sharpener because it can take more off the knife faster, and then it smooths out nicely with the finer grit polisher. I don't know how long it will last before the grit wears away, but I wouldn't mind having to replace it every once in a while.

You're measuring the angle of the clamp. You should be measuring the angle of the knife.

🤪 P R O M O S M

You should only need to check the angle of the stone and the height of the blade from a fixed point. How do you know if the top and bottom of the clamp are symmetrical?

4th gen

finally a video with real car's plain and simple good ol' American muscle

'PromoSM'