Видео

Thank you for this useful information

Good information 👍

Can you share what the main reasons are for PHE leakage into the atmosphere when putting in service after re-installation? Look forward to hearing from you. Thanks.

Can Connectivity be put in place in other Plate heat exchangers? Is Connectivity available for Alfa Laval Spiral Heat Exchangers?

When replacing a gasket, does one need to use adhesive or petro gel or maybe neither?

Thanks for the teach that sir...

How heat exchanger do for phosphate?

How to clean the plate heat exchanger without removing it (on site). Which chemical to use? Do a video?

Hai sir good morning you are videos only help me lots during PHE work.. I have one doubt regarding PHE cleaning I was try to cleaning plate with pressure washer after I using pressure washer couldn't clean it properly using a pressure washer.. It is very black and dirty Sir Please recommended something better 🙏

The Darcy-Weisbach correlation you use to relate Delta(P) to velocity is more tailored to pipe flow. Works great for a shell-tube, not sure how valid it is for a PHE. Are there more suitable ways to theoretically validate pressure drop for a PHE?

Hi is there a chanse to still get access to this tool for educational purpose?

basic stuff, great presentation but, most people prefer ignorance...

Is there simulation models available to simulate pressure drop vs flow?

Thank you very much. Excellent video.

Thank you very much. Excellent video.

Thank you very much. Excellent video.

Would like to request for phe leak test overview

Hai sir… I’ve few questions regarding plate heat exchanger.. How I’ll contact you?

Excellent explanation. Thanks.

More silliness. a snake eating its tail. you need the heat in winter. however in winter cold is available for free to cool the centers. Using energy to cool the centers in winter to produce heat for heating homes is such a waste of energy.A snake eating its tail

How can we repair air gaps on body of phe?

👋👋👋👋👋

thanks for information, need to know how capacity selection.

Hai sir I've few doubt on plate heat exchanger can you explain me?

Hai sir how are you? I hope doing well Sir we are mostly doing plate heat exchanger servicing. It’s very hard to loss and tighten the plates sir we are losing and tightening manually only sir. Is there any equipment and tool for tightening plate heat exchanger

Hi sir

Thanks! Nice video! Do You have some video which explains differential switch and how it works as heat plate exchangers flow security device? If I good understood, differential pressure switch wait until the flow make enough pressure drop and press it. This is information that flow is good. I expect if the temperature of fluid drop that pressure will rise and on the end if it is frozen the pressure drop will be max and the pressure switch will be stile pressed? Where I am wrong? Thanks in advance ..

First of all, excellent videos, it's clear and simple, thanks! What value should we aim for for the wall shear stress? I read in an Alfa Laval document about the best design practices that ideally 50 Pa would be necessary with a minimum of 35 Pa for a fouling applications. Is that right ?

How do you find the safety factor ?

Thanks.. 👍

Dear Bestio learn Sir, Hope you will be fine. Can I Access to this software for learning process. I am from Pakistan.

Great video Sir. Much appreciated. I am from India. I want access to the software. Thank you

very useful information sir, you are making the concepts clear by visuals. Actually less videos are there on plate heat exchangers concept, But you are helping a lot. Thank You sir.

how should we calculate the appropriate thickness of fix and movable frames and the number and size of bolts for specific GPHE model at specific operating pressure like 16 bar?

Hi , can you please suggest to increase the heat transfer rate in plate HE ?

much appreciated sir for ur amazing videos. it means a lot to me if u can help me out with the access to the heat exchangers software design such as plate type and shell and tube type. im a fluid mechanics engineer and im really interested to learn more.

thank u sir for ur elaborative video on PHXs. i do have a question though. based on what u said, if i want a 2" connection size, is it better to use a plate with a 2" port size at max, or use, for instance, a 4" port size plate and reduce the connection down to 2" ?

Thanks for uploading such an important video illustrating pressure drop in chevron plate heat exchanger. Distribution partner? I heard more times but I listened the same every times.

What website are you using?

More good content. Well explained

Excellent work. Keep it up, very beneficial.