Видео

Functionality...lmao...this was difficult for me to watch....looks like a Fuk it Friday job..smh

Great video! When i vacuum the outside vents do i need to unhook anything from inside the furnace? Hoses? Thanks!!

Since I'm not on your job as a helper, I can nit pick. Was your guy installing a line set? What happened to the evaporator coil? I would have liked to see you provide for the coil. I would liked to have seen a canvass connector. You have one on the return. I would have liked to have seen a cross break on your panels. Great job, nice and square,. You have minimal gaps at your corners. Since I'm retired, I would hire you guys.

Wrf why aren’t you doing the cross break to add strength to the metal? Shit job dude, and sloppy

Nice job

We found the asshole that likes to fold inside and screw it inside 🤬🤬🤬

my furnace has been shutting off and seemed those pipes, went outside and cleared the mud from the yellowjackets using an extention pole with damp sock on the end of it. had it happen 4 years ago, can't get to some of the inside pipes but blew them out with blower best i could, next summer i will be installing a screen or hosery for the summer cause i think the older the furnace gets the more comfortable these yellowjackets are moving into them, i do have the larger wire but that doesn't help with mud in there

I see the light measure twice cut once with weird angles it’s more tedious Thanks for the tutorial 😊

Why no cross brakes?

System 2000 junk!!! Lamprey bros install?

Looks great, but no cross brace?

You just made it 1000x more difficult. Cut pieces long , slide it into your S lock make your marks and that’s it. Wow 🤯

Kick the slip and drive

Why no flex collar or cross breaks

Awesome feild transition man. I use to work at a company that only made duct by hand but it was a while ago. This was a great refresher. For in the feild

Doesn't it make sense to: 1. Point them down to prevent rain and debris from going in? 2. Use a fine wire to prevent small critters (bugs, wasps, etc) from entering?

Only a true installer will look around in search of a tool and grab the homeowner’s shit just because it was closer than the van

Thanks for sharing this man. Im a service technician but I think learning how to make ductwork is very important and I want to learn. Honestly I would have removed that 6 inch humidifier bypass duct the moment I walked into the room. Lol 😆

Awesome work bro. I learned a few things for sure! I like the s clip trick! You need to upload more videos!!! :)

Too complicated, just cut the metal on an amgle and put it together

I learned from an old school lead installer on how to do transitions using Pittsburg. When I first started out being a lead almost two years ago I struggled with sheet metal and now I find myself doing all different types of sheet metal fabrications from ductwork to to even making boxes for downflows. It’s rewarding if you put the time and effort into pushing yourself every day just to be better then you were the day before.

I trouble shot using the Williamson manual and it was on point. I've watched you troubleshoot and you followed same steps. Only thing, to check 24VAC out of transformer, you connect transformer back on the board then disconnect the TSTAT connector from the board, check the left and right pins, if no 24VAC registering then transformer is called out as bad. But you were on point using a different method. I believe there was power interruption at the switch there, no need to replace the BX, but I guess its ok. However, at the end of the day, I would hire you if I needed to. I wish i watched your video before I troubleshot my boiler but since I had my manual, I followed it. I'm an aircraft engineer by trade so I love the challenge in stuff like this.

Amazing

Can atransformer partially work and turn the boiler but not shut it off?

HEY!!! Thank you so much for the video. Putting one of these bad Larry’s in today…..wish me luck!!

Great video! Please make more video like this!😊

Thanks for this video brotha. I’m trying to wrap my head around transitions and now I feel a little more confident in doing them.

Apprentice here doing residential hvac and sheet metal scares me🤣 my lead does really good trasition pieces

Absolutely beautiful work. I’m a install lead but what I lack in is sheet metal work. Striving to get better, felt like this helped a lot seeing someone do the whole process

I've used those video on 6 houses I've built. The easiest reducer and vest video making it. Thanks for the info.

Thanks for the insight. It is really helpful!

Seems like overcharged and possible liquid line restriction

This gave me a great heads up.. normally I would mark my inch for hem than my measurement. I would find myself not being able to get my longer transition inch hem because it would be on the edge I'm going to try it your way and just measure total length than fold in my hem

Get a car foaming canon and the same soap. No need for harsh specific coil cleaning fluids. Way more foam and cleaning action.

Was the owner a penguin?

If the condensers that dirty will that prevent the unit from blowing cold air at all or no Air

Hey man thanks a lot for taking your time to make this video. I think you talked just the right amount brotha 👍🏼🙏🏼

"I think we are okay" is a bit worrying to hear. Proper duct sizing and heat loss calculations is the name of the game.

Why people hung up on cross break? Well informed video boss

I have the same situation at my home. Your video helped me a lot !! Thanks

Why did you do the duct after installing the rest ? We build the duct in shop always slides in, adjust to put a flex in there and makes the job so much easier .

Watching the parts of stuggle makes me appreciate the video even more. Sometimes its a pain in the ass!

Where's your cross break

They are going to have mosquito 😂

I'm licensed plumber fitter every lockinvar has the same problem if developed length is under size nice job

I've had fiberglass window screen installed on my 96 percent Carrier furnace (59TP5A060) intake and exhaust for 9 years and never had a problem. It's installed the same as in the video with stainless steel hose clamps. I live in SE Michigan and it does get very cold here in the winter.

How much was the static pressure there has to be a back pressure thats out of this world? Great metal work though.

Remember: you don't even need a GED to get a job in HVAC.

Good video👍🏻. I learned how to do transition your way but prefer now to measure 📏 my height put the piece up mark my corners to get my angle 📐. Then cut and cross brace. Working with large pieces like your job probably would take 45 minutes to an hour

Love the hoarder basement 🤣