Видео

Well, was about to applaud you .. gee , you were by far the best how to guide video, until you f' up. The most important part. Greedy mf. Anyway, thanks for the showing us the wiring.

I would like to know how to determine how many LED lights are needed in the device? 3Watt, 6Watt... Thank you for your answer! Can it always light up inside the device?

30 feet through the sheetrock and framing. Sounds like a disaster to change the line set. Hopefully this works.

I dont belive this will work with led 😄 ...maybe will work with powerfull uv bulb.

Question...does R and C provide 24v AC or DC? The one UV light unit I got is wanting DC.

два брусочка должно быть как ножницы )))

How do I buy the smallest pump for a mini split

Why did you waste our time? This says wiring. U ain’t say shyt

Why did you waste our time?

Thanks for an informative video. It was very well-explained.

How high can the discharge line run upward?

So, how do you flush a lineset like the second one with the chemical flush? I tried similar and the fluid just ran back down and out since the easy flush kits don't have enough pressure to overcome the vertical rise.

Hey Craig. Saw your video, very understandable. However, at 12:00 you do bubble leak check with valve open on high side, but 30 seconds later do the check with valve closed on the low side.

Awesome

Necesito esto en español 😢

how do u rewire from a refco gobi II to this?

For the price of this stuff, you could get a can of flush from Autozone. Plus 5 gallons of acetone and a dozen of those butane canisters for Chinese portable burners. EDIT: Typos

I had trouble getting the tool to seal against the tube

Where did you connect the power supply?

Thank you, Craig! How did you do the recording and stitch all the sequences together? Nicely done!

Is there any difference doing this on a Mitsubishi minisplit?

I am in Florida and use the cheaper $40 single shot but will give this a try. The $40 one will break after about 8 uses.

I have a question for you. That plastic hose you just blew air into, is that the hose that goes into the condensate pump? does that plastic go all the way outside or does it connect to a copper tubing?

Hire some better engineers mine keeps malfunctioning and my pan is bone dry

My ac compressor and condenser have no refrigerant, so I need to do a pressure test on the whole system. Can I open the service hi and lo valves so the nitrogen can go thru both the compressor and condenser or should only the evaporator and its lines be checked? Same question to do a vacuum test? All the system or just the evaporator side?

How to manage troubleshooting of this pump?

Thank you so much

The foam case tells me someone designed this who has never worked out in the field, as is the case with 90% of the tools available

I bought one of these a few years ago and it still works like a charm. I love mine! Thanks for such an awesome product.

Hello. Thanks for the video. Is the procedure the same if the compressor has no refrigerant? I had a leak at the condenser and I lost all the refrigerant. So, same procedure with all valves opened? Thanks

So to install it do Ineed to take off the shroud that it is attached to. I don’t see any bolts on the unit to,attach it to the furnace.

I need to get this motor aligned in a 4" hole. I don't want to take all day. Do you know how much a day is?

Reduces call backs my ass, I’ve been back on the same pumps 4 times, constant clog issues.

I need 4 inch metal blade for nutone br heater.

At least I like that they've improved it the first two models having the threads in the same area as the cold temperature it would make the threads swell up and overtime eventually you couldn't unscrew it by hand then you would leave it slightly loose so you can get it unscrewed and the cold temperature just end up being too close to the threads and it ruined the unit, being this one the threads are at the bottom nowhere near where the outlet is they'll probably last a lot longer...

do the pigs go through couplings?

I have one of these near my furnace. I watched this video because I don't know what it does. Now that I've watched, I still don't know what it does.

Most minisplit its alot harder to expose the shroud to be able to put the strip in. The netal grille and side to side louvers can be a pain to break down to make shroud accessible. Wonder what brand minisplit this is?

thats all cool and all but where does the water go if you have no drain pipe in an inside room, a bucket on the floor?

Why not use a setup without all that fancy shit? Gauges and vacuum

waht about the slim duct

just wondering why you'd hookup 2 shrader core removal tools togethor for your micron gauge when you could've just hooked the micron gauge to the one shrader core removal tool just wondering

What is the model of your hilmor pump? Great video and thank you

please provide the product model. I see lots of product has sensor and pump apart but in combined one case

Does this kill viruses? Like covid?

Your guys’ lineset covers are awesome too as far as installation goes

This seems like a good idea for killing germs but it also seems like it would be very airflow restrictive. What effect does that have on all the other system components and the HVAC efficiency?

These videos have me reminiscing. Keep it up Mr. Migs

What do you do if your coil is in the supply plenum directly over the furnace cabinet