Видео

Giver hell J-Dog🤘

i did this 2 days ago. was pretty dang easy once i watched you. ive got an m-tronic version and when i cranked the saw it didnt seem much difference maybe just a little louder. Then, i did a forced calibration and holy crap! its like it found a new gear, completely different saw now. thanks man!

Did u juice this one up buddy

Pretty poor quality, I know they have plating problems but thought they could manage a good piston! I just purchased a pop up Hyway for my 266/268 I'll have to a good look before fitting it😉 I generally buy Meteor but none available here.

Good running 395. I love ‘em 😎

They both runs good brother

Is this one you’ve worked on and now selling?

I have a 440. The carb is finicky & it'll run different with canned mix vs self mix vs ethanol free vs ethanol gas and need readjusted if you switch fuel. I've rebuilt & replaced the carbs 5x. The fuel metering diaphragm doesnt last. It runs great for a firewood season, then runs like the beginning of this video after sitting a few months. ANY water in the fuel will foul the carb. It wont clear itself of water blocking flow through the fine internal filter. I tip my fuel can upside down & let any possible water settle to the end of te nozzle, then open & close it quickly, letting any water out. Then I add a little mix oil in case some settled & came out too, just to be safe. Modding the exhaust rgives it more power. The new x-cut chains cut great & draw less power.

Good to see I am not the only one that owns or uses a 039

I did the top end on my 360pro and in 5 minutes it locked up again and I swear to you I’m running the correct mix gas. I don’t understand it. What should I look for

Right on Thanks bro I have a 445 and it's the same set up as your 440,,thank God I couldn't find a fule line replacement video for my 445 , your video help 100% thanks man

where are you located I have two chainsaws they're both 036 Pros I really would like to have them rebuilt could I ship them to you

where are you located could I ship you 2 036

wow thats a strong running little 260 that bad boy looks like it cuts as fast as my ms310 i have 2 260s think one of them is a pro both the oilers went i was going to fix but i put off on them because wanted to learn to port first think i have like 11 saws lol only got like 5 going right now missing my 046 and ms460 tho there down so useing my back up 372xp

that is Impressive for a 55 wasn't inspecting that imma have to keep a eye out for a 55 now

im a fan of the 357 i call it a mini 372 looks like the rankers were little hungry lol reminds me i gotta do the top end on my 359 oh question is the 61 have the same bottom end as a 272xp or what saws have the same bottom end of a 272xp i have a 272xp ran great for like 6 months died slow like it was running out of gas i replaced top end i have gas and spark and it wont even try to start i was thinking maybe crank seals but havent split any cases yet

i know and do work on saws a little as far as doing a top end and rebuilding carb haven't split any cases yet and i need to i have 2 ms460s that need crank bearings but anywase my question is everyone sez a 036pro is the same as a ms360 i have a 036 pro has alot of compression its oem stock and my buddy has stock ms360 and the 360 kills my saw even my ms310 is way faster then my 036 pro are the top ends the same on the ms360 as the 036pro

A bit low in the water, but I'll bet you could put a few more on there

Где здесь 61 husqvarna? На видео только 357 husqvarna...

I think you made a mistake- that was not a 346XP, but rather a 346 XP NE with the chain cover painted orange, or you meant to say 3.4hp in the title. It also helps to add saw ID captions if you are not going to go in logical order. Lots of backwards going on here...

Did it run ok with the pop up piston? I just ordered one from hl supply for a 261c that came cheap because the guy couldn't sharpen his chain lol never seen a bar and chain that had been so roughly treated.didnt want to spend much as I'm not sure what other damage has been done.

Stihl bar?

2nd saw sounds a bit tired haha

Is that a 24" bar and skip tooth on that 61?

Awesome video man I appreciate it

😅

Must have jiggled that carb for 2 days trying to see how to remove! Saw your video and the torx screw buried in the handle -- WOW! THANKS!

You mentioned these were simple to work on I have a271 looks identical to the 261. Had to replace fuel line found it to be tedious to say the least every thing so tight, but got it done. Thank you for your video helped a lot.

I’ll keep my 036 keep your Husky

Nothing like a croc full of chips. Lol

Awesome saws 👀 👏 😎 I purchased a 5105 off eBay and be here this Wednesday 😀 very excited. Looks like very good condition 👌 like you have fixed 👍 Washington state coast 😂🦅🦅🦅 Gray Eagle 😊

I'm thinking about doing the same setup on my 036 pro. Just curious, did u run a squish test on it after doing the base gasket delete? Should I do a squish test? Since it is a pop up piston, do i have to do the squish test differently?

Скажите кто знает,можно ли поставить поршневую от 353 на 350 хузварну ,спрашываю потому что у нас в украине нет в продаже поршневой 44мм?

Какие цылиндро можно поставить на хузварна 350?

Very nice video, thank you taking time showing us uow to do. 😊

I have a 036 and i put a new top end on it. The one i bought doesn’t have a screw to hold the to hold the top plastic in place what should i do?.

Nice chips. Chunk looks wet.

Die schneidet 👍

Helo

Stock they rip

Hello

The Stihl is a saw that a homeowner could push through on the dogs with a dull chain, the Husky will run faster and smoother than the Stihl on higher rpms with a sharp full chisel chain, without being dogged in. Like both saws , but love the 3 series Huskies. ❤

What was that white grease you put on? Some kind of gasket maker?

New Sub, Thanks for this Awesome vid!!!. Just got a 261c that's seen better days...this is helping me refresh it. I have one question: I am using Lucas assembly lube-semi synthetic for rebuild-Do you think this is a good idea? Thanks Again!

I really wanted to watch a video but whatever you were sucking on was annoying. Next time try not to suck on something when you’re doing a video.

Muy superior la stihl

I find my 670 is really heavy is the 61?

Hey again heh, Something strange happend, the dealer`s small engine mechanic, whos a veteran and our local pro to say it in that way, tried to replace my cylinder and piston today. I owe a 2152 jonsered, or a 353 if you will. the new parts was a un-original 346xpg, or a 2153 cylinder and piston. he told me : the original inside my 2152 was a 45cc, and the one i wanted inside the jred, the (346xpg) was a 44.5cc so he said he couldnt fit them could it just be as simple as someone just sent me a wrong cyclinder? x) anyhow, good evening :) PS: Could it also be that there are different year models with slight modifications between the saws?

The Husky 61 holds a special place in my heart because my dad had one for 33 years and then it was stoled.

👍👏👏👏👏🔥