Видео

Hello good afternoon. I have a GNX3 Digitech pedalboard, stuck at startup, firmware 1.5 When doing the hard reset, it freezes at the end, when calibrating the expression pedal, can you help me solve this, I'm from Brazil and here I haven't found anyone who understands enough to solve this.

Olá, boa tarde, me chamo Jaziel Santos. Tenho uma pedaleira GNX3 Digitech, travada na inicialização, firmware 1.5 Ao fazer o hard reset, ele trava no final, na hora de calibrar o pedal de expressão, voce pode me ajudar a resolver isso, eu sou do Brasil e por aqui não encontrei ninguém que entenda ao ponto de resolver isso.

What’s the screen model??

How much volt for your rc circuit please?

I’m facing the same problem with my MXR noise gate pedal I’ll did same thing & I’m fix my pedal Thanku so much for shearing your knowledge.

Hey man i have the gkmb115. I checked the fuse and its fine what would that mean in that situation? The LED turns purple when turned on btw and no sound or usage from the amp.

Didn't understand a word so thank you for sub titles. Very informative.

try using rev log pot, would be nice

Thanks a lot, fixed my amp that went out after a storm during a gig. It was two of those Fets and a fuse. Very thankful!

Hi. I have a problem with my digitech rp2000 expression pedal. It is not functioning. What should i do please

I replaced the TDA2030 and the fuse but still no amplification from input and humming loudly. The TDA2030 is heating up fast too

hello professional. what could be in the thai stove the clear sound channel is distorted? Regards

Anyone can explain what he did in English please

I replaced the 500k pot but now I get no sound when it is on -only on bypass 😢

This was really interesting! Except I was wondering why you used the ground connection from the filter cap (C18) rather than any other ground? For me it gives the same result whether I use the chassis or c18. Also on my amp the result was the same - noise from the preamp but there's no problem with the V1 tube itself. I had already changed the filter caps so is my next step to check all the caps for leakage before cap C6?

Em ở đâu vậy? Anh cũng có 1 cái bị hư không ra tiếng. Bybass thì ra. Trống cũng còn. Em có thể sửa chữa được không?

Đồ trẻ trâu , bạn dán cái gì lên cay đàn za,

Rất hữu ích, thank you!

Chao a có bán phụ kiện đàn không a bán cho e 2 cái volume có tánh coi a25k không a

Bạn có thể giúp mình kiểm tra pick up còn hoạt động hay không hoạt động bằng cục pin được không mình rất cần, cảm ơn bạn rất nhiều

I have a vox vt30, but now there is a problem. if I play for 30 minutes, the sound suddenly decreases and hoarse. what's the problem?? Please help me. Thank you

Bạn ở đâu, có nhận thay pu ko

Quá tuyệt a ơi <3 a làm thêm 1 phiên bản có thêm màn hình để đặt tên cho từng patch đi a

My guitar amplifier dont have footswitch port.. only select button to active the boost drive.. plase make video to make footswitch port and still have select button

qua hay

Kop Kuhn krub sir

Sir can you write down the wiring of that test bulb thank you.

That is pretty spohisticated coil winding machinery - how many people have such fancy equipment at their disposal?

Hello,goog video, do you know the fet's numbers or where can i get the schenatic diagram?

thanks for posting this :-) going to do the same with my old pro jr. might get a 12ay7 or 12at7 for that first tube slot to make the volume knob more managable at low volumes. thanks again

Thanks! Mine plays, but is frozen on one setting. Buttons, scroll (data) knob doesn't do anything. Could it be battery? something else??? Suggestion greatly appreciated!

so as mine .. vox ad 100 vt xl . bad .

Sounds like you fixed the noise but it isn’t compressing any more lol

Xịn qá a ơi!

go buy a voltmeter and set it to continuity and save yourself the risk of shocking yourself sheesh.

How does amp sound compared to Vox AD120vtx?

Nice video

Sir, what is your FB account? Can i ask you about my rp2000 has broken also

This is awesome. Thanks for the video !

Not used full ,how to know why fuses blown up /burn

Dear Mong, thank you for sharing and showing us how to set apart the main board. Kind regards from Mexico amigo!

Hi, what value do you use for the potentiometers? they are logaritmics?

WEAR SHOES DANGER HIGH VOLTAGE

Anh oi giúp e voi.cuc me8 của e hay bị nhảy nút tuner mặc dù e k có bấm nut đo.đang sử dụng tự nó nhảy

Thank you for subtitles. I only speak english and I really liked your video!

Hello I see that it looks like you have something attached to the bottom of the inside of your amp, and it looks like it has something to do with the power source of the amp. What is it and what is it's purpose?

I am having the same problem, please provide me the address for purchasing the spare parts

Guitar hk có nhún mình tự chế lại dc k bạn

my friend your accent is very strong. Could not understand a word of what you were saying. great video. in my VT100 the valve tube does not extend out of the chassis. There is no hole, must remove chassis to expose tube...

Bạn liên hệ chỗ này nhe ‭+84 93 8299604‬, randymod.com