Видео

😂 they're not worth that much .I know what they're worth!! Not in that condition they're gonna leak too u know

Hands down no contest, Members Mark Oven and fryer cleaner in the spray bottle from Sams. I use it to clean pick up tubes, timing cover, oil pan and rear covers on the LS engines I build. Nothing works as well on baked on oil, grease and dirt.

Get superior dark fury from orileys

You working!!

Steve<<<< Raises Hand Did someone say Trial and Error? Just Part of Custom Build's Brother But as long as you Keep that GREAT ATTITUDE It Will Work Work Out Fine 1 Step Forward and 2 Steps Back But Still Great Progress Man Keep it Up

Great content, as always! I need some advice: I have a SafePal wallet with USDT, and I have the seed phrase. (alarm fetch churn bridge exercise tape speak race clerk couch crater letter). How should I go about transferring them to Binance?

Definitely looking good Merry Christmas 🎄

I would try and measure between your pillars and take that measurement and add a 1/8 to it and cut some tube that length and cut your tacks and shove it in and re tack it and see how your doors close and go from there. A good tip to chopping up a car is if your doors close good take them off and take some tube and cut and drill some mounting plates on the end to mount on your A pillar where your door mounts both positions and triangulate to the striker plate where it bolts in so you can climb in and out if need be without opening to work on things .

Grip load of parts for Courtney

1973 Pontiac Firebird/TransAm NEW OEM HURST DUAL GATE SHIFTER This is similar to the gto shifter.

I worked on British motorcycles and use industrial strength easy off oven cleaner

Have you tried oven cleaner

The tin canning effect is common after bead rolling. Mount panel and spot weld it in when ready. Cleco/screw in mock typically don’t work work with this bc there’s still play. After it’s in use oxy/acetylene or oxy/propane torch to heat areas around panel then follow with cold rag soaking in a bucket of ice water. Do it from center out and work as you go until it’s shrunk enough and the “tin canning pop” will go away.

Cool 😎 ! Had me on the edge of my seat waiting for the trans adapter falling to the ground 😅

What were the youtube channels that encouraged you?

From 10 feet away, they look awesome!!!

Regular old black metal outlet covers and switch plates would be awesome, plus metal or wood is always better than plastic!

Do it yourself stud finder!

What guage sheet did u use

Man do you know who makes the hood on that car? Or who owns it so I can ask them by chance?

Great job and explained the simple way

Merry Christmas little late happy new year too the family

How much to pull out out alone?

Merry Christmas

Hope you had a good day all day. I think you are doing a great job on that old car making it cool. It is going to be so much fun to drive. I love it.

Winters has shifters you can take out the box

nerry Xnas

This car is going to be a big hit at the street rod shows ! 🏆

Is this a Dana 60 for a Ford truck ?

Cool 😎 !

Happy holidays from carter boys!

Man the first time I cut a 9inch down was terrible had to do cut it back apart a couple times great video merry Christmas

hey courtney this is herb from michigan muscle car garage, got your from glens hotrod channel, i believe in supporting each others car channels, we are a small group on the youtube community, have a merry christmas 🎄🎁

HAPPY HOLIDAYS to you and yours

Merry Christmas to you and your family.

Thanks for the forecast! Just a quick off-topic question: I have a SafePal wallet with USDT, and I have the seed phrase. (alarm fetch churn bridge exercise tape speak race clerk couch crater letter). How can I transfer them to Binance?

Merry Christmas 🎁🎄 💪

Merry Xmas. I’m on the finish building the garage project. Electrical then insulation. Then cut up a 06 Dakota to get some money. Then after that 97 f350 rust repair and turning it into a tow truck. Then hope to purchase a osb Chevy for the power train and sell the part. Then move the 47 fleetline in and put the power train in that. Get it done. Power train glass seals little rust repair have an interior from a Acura rs 2nd Gen to go in. If I do win I’ll even pay the shipping to Winnipeg.

Merry Christmas to you and your family. We're working on a 2000 Jeep TJ and a 1966 Plymouth Wagon. Love your channel and your Facebook page. You guys really rock,especially the little one ❤

Courtney me & my drag race he ran a jr dragster & I ran my 64 nova in super pro bracket racing but now we’re running a legend car circle track racing that’s what he wanted to do so I said okay them things would help us a ton I watch all your videos

Working on an 86 fox. Would be nice for future sheet metal fab

I doing a small build with my son working on my 2001 honda civic for my 16 yr old son. We love your new build. It's going to be amazing I bet

Thanks for what you teach, inspiring this old dog with some new tricks. New year project is my 68 Lemans for drag and drive. Rear quarters need patch panels and mini tubs to tuck a 28x10.5 radial.

A #30 drill bit is made for your copper color cleco

building a s10 race truck. i just might be one of those guys that watch every video lol

The factory back then had the bead rolls to the inside because they used thin wood and cardboard to make the panels to lay flat

Merry Christmas. God bless you and your loved ones...

That’s me seen them all and merry Christmas to you and your family

Thanks Buddy for letting me into your Life. I appreciate You Courtney.Happy Holidays to the Family and all of Our Extended Family.! Great Community!.

Merry Christmas to you and yours. I watch every one of your videos. I don’t always comment just know I’m watching. If my name is drawn please pick another. I’m a biker let alone the skills to do this.