- Видео 21
- Просмотров 129 045
AgOpenGPS
Канада
Добавлен 24 фев 2021
AgOpenGPS is an open source precision agriculture project built by farmers worldwide, who are interested in learning about the software through building its hardware integration. It uses advanced GPS technology to perform precision tasks such as auto-steer, auto section control & mapping, automatic turn around (U-turns), machine control, tram lines, rate control and it's fully open source (free to use & modify) and highly customizable.
Видео
IMU, CPD, Ackermann and wheel angle offsets
Просмотров 1,7 тыс.2 месяца назад
The basics of IMU, CPD, Ackerman, wheel angle offsets, and what they mean in your situation.
agOpenGPS - startup and connectivity check
Просмотров 3,8 тыс.7 месяцев назад
If you're wondering why AOG hasn't connected to RTK or to your steering board, this short video is for you !
Tramlines
Просмотров 3,1 тыс.9 месяцев назад
How to use tramlines in agOpenGPS v6 - note that in this video, we purposely picked a seeder width that didn't quite fit the sprayer to show how to handle such situations. Sorry, had to fix another issue in this one - hopefully this is the final version!
Field Operations
Просмотров 8 тыс.9 месяцев назад
00:32 Create a field 00:45 Creating a simple AB line without boundary 01:25 Creating a boundary 01:35 - Using Bing to record a boundary 01:55 - Recording a boundary using tractor 04:00 Creating a headland (method 1) 04:40 Creating a headland (method 2) 06:30 Creating a simple AB line 07:05 Creating a line from heading 07:28 Creating a curve 07:55 Creating concentric tracks from boundary 08:30 I...
Machine and Implement setup
Просмотров 4,1 тыс.9 месяцев назад
A quick guide to show how to set up your machine and implement
Understanding PWM
Просмотров 4,7 тыс.9 месяцев назад
The settings on the PWM tab are frequently misunderstood and if you get them wrong, you will never steer well. Here's a guide on how to understand them so you can get them right.
AgOpenGPS - an introduction to the interface
Просмотров 9 тыс.10 месяцев назад
This is a basic introductory video showing the features and areas of AgOpenGPS - it will be used as a point to link videos that explain its features in greater depth.
AgOpenGPS 6 - configuration and first run
Просмотров 8 тыс.10 месяцев назад
Chapters: 00:00 - Title 00:18 - Download and install 03:22 - Flash firmware 04:50 - GPS configuration 05:30 - Teensy configuration 06:00 - Network configuration 06:50 - AgIO configuration 08:00 - NTRIP/RTK configuration
Explaining the All-in-One PCB v2.5
Просмотров 8 тыс.Год назад
Explanation of AiO PCB v2.5 github.com/farmerbriantee/AgOpenGPS_Boards/tree/master/TeensyModules/V2.5 github.com/farmerbriantee/AgOpenGPS agopengps.gitbook.io/agopengps/ Updated PCB (v4.0) currently in testing phase as of March 2023 If you want only guidance without auto-steer then this is the RTK capable antenna receiver we use. It can be used on its own with AgOpenGPS plugged in via USB. www....
Creating a Multi Boundary from KML file
Просмотров 2,7 тыс.3 года назад
How to create a Multi boundary by importing data from a Google Earth KML file.
Creating a Simple Boundary from KML file
Просмотров 3,3 тыс.3 года назад
Creating a Simple Boundary from KML file
Download & Install AgOpenGps, First run
Просмотров 15 тыс.3 года назад
Download & Install AgOpenGps, First run
Thanks for this, very helpful. Could I suggest that U-Turn setup could be also be a helpful video? Or a updated video on Turn Compensation.
for can bus minimum to move should be 0 ?
👍
Hello sir i need auto steer system in my john deere where can i get those all PCB's?
This Video are great Help for me! Thanks 😊
Dont have ethernet cable connection. so ı cant use udp ı cant connect to steer and ımu etc... What should ı do?? I just want to use agopengps with microsoft airsim
usb to ethernet converter
what is kia?
What is the latest version of agopengps that supports the older arduino nano based boards?
AFAIK the older boards are all still supported.
Which is that so tiny PCB? I've a Kaupoi one but is absolutely diferent!
Can you do a video on editing a recorded path? Lets say I am using the simulator and make a wrong turn while recording. How would remove that section and then start recording again the right way. Possibly needing to stitch a few paths together.
I recorded a field, then brought the data to my desktop computer at home to set up tram lines in the simulator. How do i located the tractor in the simulator in the field? I am also at the tips and tricks part of the video where it is showing an existing driven boundry, then pulling the maps from the maps boundary icon. i'm using vrs 6.3.1 and i do not see the boundary option. The top of that menu in mine says headlands.
Check you haven't turned boundary icon off, some are seeing it missing as a default that way. Gear icon, near the bottom
You just need to zoom out and drive into the field
;.i like this video and i have been able to complete all the steps you have described.I only miss the part co connect a keya type motor to the steer box. i m not able to understand what s wrong. do i need a specific twisted cable for the can bus connection ? do i need to put a 120 ohm resistance in the can bus loop ? Best Regards Emmanuel
This video has nothing to do with that - read the Keya topic on discourse forum, all info you need is there :)
Great thanks! What are the numbers on the top left and top right for? For example at 3:21 The 14.0cm and 267,2 ?
Fix-to-fix distance, and heading
This is extremely helpful. Thank you for putting this together!!!!
Does it useful for row crop cultivaotr?
For anything you like! But for row crop, perhaps an AB line might be better.
@@AgOpenGPS thank you !👨🌾
Great!
Another suggested use - suppose you are spraying an established field you didn't plant. You can see the tramlines in the crop, so engage Recorded Path and drive them. Then, when you next visit the field, its all there
You operate with the menu buttoms too fast. It is Hard to follow because i have to guess what the meaning of the diffent Buttons is. Please slower.
I still need to fix subtitles on this one, but remember you can play the video at half speed via the gear icon in youtube ?
I use this feature all the time i our orchard. The trees were planted in a straight line but replacements for dead ones were never spot on so using the AB lines doesn't always work. The recorded path will also record the speed, section control etc At least it did in older versions.
Thank you very much
Super!!!
Thank you!!😎
Thank you!!!
Thank You, this helps me alot.
These explanations are of great help to better understand how to use Agopengps. Thank you very much !
Thank you!!
+++
Thank you, we need this project to keep going.
Indeed, this helps a lot!!
More videos like this, this is golden!
good info
Amazing help this video was, now all I need is the hardware now I have it installed on the laptop/tablet .
This is great help!! Thank you!!
Thank you very much for the videos!!
Thanks for the videos
I hope the videos keep coming I'm trying to get setup
I updated my single micro F9P following these instructions and AOGConfigOMatic but I no longer have connection to my gps (it's no longer green as seen at 7:42 in the video) however my steer and IMU are green. Has anyone else run into this? Which is the correct bin file for a single rover, and are we updating to (1.13 SingleAntennaRover.txt) or (1.32 SingleAntennaRover.txt) as both seem to exist depending on where you look.
Good job! It's amazing how the project is developing :D
Good job ! Thank you :D
Sir, What a Great work! But I believe it have a place for User Interface improvements. I would recommend a book called "The design of everyday things" by Don Norman. Keep going!
Thanks for great work! +2 tractors with this system
Hi I am a Precision Techgronomy student At olds college. I am wondering if it would be possible to get someone from AgOpenGps to speak to the Precision techgronomy club on campus? Thank you
Sorry, there's no one really monitoring the channel. Checkout the agopengps forum (search or see links in channel)
I'd like to run it on a track machine, so how would I do that with no need for a WAS Thanks, have a great day
Check-out the forum discourse.agopengps.com/
Can I run it without using a wheel angle sensor, using a gnss receiver instead?
Any one in this community make video on only guidance without auto-steer then this is the RTK capable antenna + receiver on agopengps from start to finish it will be much useful for the non teechi farmers like me .... Thanks for the contribution to all .....
Very simple. You need only tablet + ardusimple rtk2b basic starter kit. Ardusimple is connected with usb cable to tablet.
@@matej4946 what tablet - i thougth agopengps can only run on windows?
Can assembled PCBs be purchased?
I also want to purchase a pre-assembled PCB for testing, in future I would like to purchase more if I can mange to set-up and install it.
@@trinityklinkert9021 let us know if you find it please.
Yes you can, check-out the forum discourse.agopengps.com/
Can it be used in China
Components are almost 100% sourced from china :) Take a look at the Boards repository and the Wiki
@@gunicsba thank you
Which pcb version is this? And link please🙏🏻
Hi, What updates are included in PCB v4.0?
very informative, thank you
I don't believe a farmer reached this level. I am very happy to accompany Brian in this experiment. I am sure that food production in the world will only be viable with technology.