Видео

Hi, I looked at your video of fixing the 18 volt Ryobi battery.. my battery green light all four lights keep flashing constantly and won't stop. What can I do in this case? Thank you

Ways Ryobi will make you buy a new battery. Thanks for the hack.

Didn't work for me on a PBP005. Also there is a plastic plug covering the back left screw. I heated the driver bit to melt through the plug since trying to pry it out with a small screwdriver was unsuccessful

You’re a legend, mate! Saved me mucho dineras.

hmmm you described all symptoms perfectly, but reset did not work?

Hello, could you please help me? How can I reset the BMS of a 1.5 amp battery? Will you have a video? Please share the link with me. I would greatly appreciate it.

This is a great video but for the price we should be returning them maybe then they will correct the problem.

Thank you!!! This worked perfectly on my 6ah HP battery saved me $140!!

Hate to disappoint everybody,the voodoo doesn't work

It's not acceptable that you should have to do this to a relatively new battery.

i have a 18v 4Ah Ryobi ONE+ battery that stop working. push the battery button and it flashes 4 times. when I try to measure voltage between terminals it jumps from10v to 0v. I went ahead and opened the battery and measure the voltage between terminals at circuit board level and got 18.61. I measure the voltage between the suggested jumper points and got 3.7v. I jumped making sure it was 0v, pushed the button and got 4 blinks and off. close the battery and put it on the drill tool but did not work. I plug the charger and the solid red no green indicator comes up, pointing to the very left where the temperature icon is, but there is no battery on the bay. With 0v across terminals and 18+v across terminals at the circuit board and no working with a tool, I am confused..... is a charging problem or a battery problem ?

Gracias me funcionó 😊😊😊😊

Every vid I've watched tells you to short different circuits

Thank you verry much you deserve a like. 👍

Thank you

Good word, Brother. Thank you for sharing. Paul Creason

This is for batteries that are out of warranty. If you remove that plug, your warranty is void and you won’t get a replacement battery in your battery might be.

Outstanding my friend! My battery is a 3AH so the jumper spots were smaller and a little harder to find. But once I found them and followed your instructions- bam! Light reset and charging like normal. Thanks my guy!

Worked good, thank you 😁

100% Awesome. I had done the jump start and had voltage in the cells, but the charger still indicated a bad battery. I assumed there was a safety on the circuit board but had no idea how to reset it until I found this. It worked like a charm. Thank you!

Hi Larry, I have the exact same battery with the same issue. Battery was fully charged, and the charger shows a solid green light as expected. However, the tester button flashed 4 time and no power is outputting. Opened it up and tested the batteries as shown and getting about 20 volts. Tried the reset jumper, it flashed all 4 LEDs then flashed only LED number 2 and 4 during the jump reset. Am I missing something or is this batter gone?

Thanks a million, battery is ready to go!

Awesome, worked perfectly thanks

Soldered a red wire on the positive and a black wire on the negative. Melted two indentation on the back end where I can thread the two wires separately. Closed the cover, and viola! no need to ever open it again. I just have two short wires (so they never touch) I can tap with pins connected to a 12v while on the charger. 😀

Fixed my battery. Thank you for the video

Great hack but opening mine I find that it's a different control board with no well defined at T2 or J1. Battery has 18+ volts and each cell is about 3.8v but still won't charge so I'm assuming it needs this reset but I'm afraid to start shorting out terminals on a lithium battery unless I know exactly what I'm doing. Thoughts?

Tried this about 6 times. Never was able to get it to work.

Thank you for sharing the message about our risen Lord and Savior Jesus Christ.

I have been buying tools from auction that come from Home Depot. Had a combo Drill/Impact kit (new customer return). One of the batteries was dead. Checked the cells and they were all close to 0 volts. Jumpered the cells with a good battery. Voltage came up but still flashing Red/Green on the charger. Repeated this 2 more times; voltage was now about 16 volts across all the cells. Still no good. But now getting all 4 LEDs flashing 4 times when the button is pressed. Jumpered J1 and T1 as per this video on a PBP003 battery. It has the same electronic board as in the video. Pressing the button now yielded a single LED. Put in on the charger and it is charging fine. Thank You for the video and the great explanation!

why post this with a good battery?

Worked for me on PBP002. Thank you so very very much

Thank you Brother Mitch for preaching the truth of God's Word

Great trick, thank you for this! I have the same battery, and it was a full charge, just needed the reset lol

mine ryobi 5ah battery when pushing blink 4 times all green lights, i dissasembled it and made reset like you but it not work , still blink 4 times... i checked volts on battery + and - down there i see 19.72 volts, and when checking up voltage in place were sit in to charger i see 0.4 volts only... up top i checked + i have but negative not come up . when i put in to the charger battery on the charger blinking only 1 red light . battery to hot light.. quess its done....

Thank you so much, Larry. my Ryobi battery 18v 4ah working again. I got another 18v with 6ah. I will try this method. Again, thank you so much for your video tutorial. 😉

Your message about not messing with it should have been at the front of the video.

Thank you! 👍🙏

Larry, you are an absolute genius. Thank you so much for posting this. Worked like a hot dam on my PBP006. I honestly really appreciate it. 👍

Promo sm 🤔

I have been trying everything to get this battery to recharge. I pulled it apart and checked the actual cells and everything was fine. But the part that goes into the charger read zero. Your video is the one that showed the resetting of the battery. it got to cold. Thank you.

Did it cross your mind to tell us what the security bit size was?

Yellow jumper wire............

I have one of the new ryobi batteries it doesn’t have the t2 j1 to reset it. Any ideas ? Thanks

Спасибо дружище за полезную информацию!

Is this the same procedure for a 2amp hp battery?

Worked like a charm! Thank you!

Surprisingly enough voltage was 26.14 so it's still under 90 day from Home Depot so I'll get another. Just odd that it didn't work. Yes I found T2 and J1 . I get 1 blinking led then after shorting it the LEDs just cycle continuously.

Does the warranty work even if you didn’t buy the battery new your self but it’s under 3 years old?

I did it but leds just keep cycling. What next?

i have a very old ryobi i havnt used in about a full yr., and from watching this i understood how the circuit board will switch over from blinking red to charging green only after it reads a small amount of power from a battery but initially it does provide a small amount of power with a steady red just as it is plugged in so i plugged and unplugged it about 4 or 5 times with the battery inserted then the battery charger finally agreed to switch over to charging mode with steady red and blinking green light...