Видео

I low-key got so bored that I had to look it up

can you fix my black brick 15” brick house? needs recone.

Great job bro ❤️❤️❤️

I went to the url for sub parts in the description and it took me to a spyware page direct Apple iPhone support scammers in India . Idk if there is a good working link to get subwoofer parts from if there is please lmk .

I have a few gems laying around a Rockford power hx2 15” with a bad coil a 12” earthquake San Francisco 1990 competition sub fully functional . A Rockford power hx2 12 with a broken tinsel lead . Another Rockford power hx2 with a cracked basket Also have 2 12” Cerwin Vega 12d4 originals and a Vega 10d4 . I’m looking to do something either repair them all or improve them if possible like the HX2 I know there’s better options for tinsel leads . I’ve never repaired any speakers though so I’m not sure where to begin .

Its 2024 and is this is still one of the best videos for building a subwoofer that I have found on RUclips....

Thanks

Do u still fit subwoofer

Do u have 110 mm bolt pattern baskets like a 12 spoke or a adapter that will fit other sizes to 110 mm?

I have a question....I recently was sold one of these 15" silverbacks lloll and its failed up is it worth it to rebuild it or chunk it as a loss and keep on learning...I only give $30 for it and the rubber looks great just voice coil is trashed.....let me know what you would do....thanks a lot

Murphy is real! Glad my interest in speakers came across you. Thanks bro, hope all going well, peace!😊

Nice video dude , i work in restoration , car audio as a hobby. The reason i commented is i work the disaster relief for Hurricane Harvey I was there in Texas helping everybody for like a year and a half. Rebuild . Nice to have found your channel.

The original Juggernaut was a DD OEM. Subsequent ones were cloned in China for MMATTS to reduce cost. Thanks for the video. What u up to nowadays? Time for a new video pimp.

Skipped right over the part I need help with

Can I use a 2.5" long winding coil with a 3.3 gap in the motor?

💪

This is great! 👍

Great video and great information brother

Is your weight a ham radio dummy load?

billy bang tnite nice

Hey dude could you rebuild a Kicker C10? It was frozen when I got it. But I did the drop it on it's face method to get it unlocked, not the coil is scratching/rubbing.

It comes with a high quality low tolerance resistor because it matter most in calibration...you want your calibration to be as close to spot on as possible for accurate measurments...if it came with a 10% resistor instead of a 1%...all measurements would be off by that much...pretty big difference

I got some old steel waters need to be redone

I came to watch a build and went on a whole DJ Magic Mike trip after the intro

👍👍

No one ever says on the leads Wich is positive Wich is negative. Great video.

Great info still here in 2022

Nice

Thanks for this video. I have done a ton of recones DC , Sundown but never have built one from individual parts well all that will be changing. My biggest question I have for you is will it be easier to build a recone first or build it in place after I get the ring ca'd below the spider and triple joint done.

The King of Glue👑🌪

How do you decide what parts to use and know how they will effect sound, enclosure, etc?

Thanks for this.

Hello, could you recommend the glue you use, the one I use is not that good, please?

Ok

Thanks for sharing...

Well that sucks I just threw my two Kicker CR-V because this guy that is well-known( EMF speaker guy)on another Channel told me that it couldn't be rebuilt and i should just throw it away! in the comment section haha I held on to those speakers for like 2 years after a stereo shop had blown them with a bad amp installation along with the dd dm 2500 amp

I am new to reconing speakers and I have watched 100 videos and nobody has broken it down like you and actually explained it the way you do and make it easy for anybody that can read a measurement

Cool Vid Brother, Thanks for taking the time and sharing quality knowledge!!

Sir how select gram for add mass

I dont know your name but thanks a lot CMD Audio. With all the information you provide and what mesurements are needed I was able to mess up a sub and then compete 2 others after. One is still running strong and I blew up the second one I built. So I'm back here again for a refresh course since I need to build this one a third time 😂 this time I'll try to actually follow your directions and build it like a drop in. I was doing it spider and coil into the basket first and if was aligned great then when I put the cone on it pulled to one side a little bit. Just wanted to thank you for this amazing peice of teaching gold this video was.

Nice one thumb up

Hi... is it possible for me to use the magnet and basket of a midrange speaker to build a 5 inch subwoofer..? If so please may you assist me.. I have very little experience,, but lockdown has made me ambitious..

🙋🏻‍♂️

I'd like to contact you for a build

I know this is an old post but your math is off. X-Maxx is calculated by how far the speaker will move with the windings still in the gap with a 2-in winding height and 1/2-in top plate you will have 3/4 of an inch of X-Max one way or 19.05mm

hi please >>> can you tell me what is the exact position for the voice coil inside the magnet like if the magnet thick is 4 cm and the coil winded wire is 2 cm thx

thank you for your work

Hey dude i know this is a while ago but your my only help! , so if a 10" basket has a voice coil exit of 3.5" , can you have a 3" coil and a 10" cone with a 3" VCID?

what glue should i use for voice coil, cone and spider

I currently have 2 Skar audio TXL 18s. They have the 3.5 coils, 6 spoke baskets. I think the factory cones are the same as what you use in this video. Do you think I could rebuild them with say TI baskets with 10" spiders, with a tall or mega roll surrounds so I could get more xmax? Or would it not be worth the trouble. Just wondering. Thanks.