Видео

Sir 80% or 8cm vcut yan ay 43.7 degree..ang tamang vcut ng 45 degree ay 82.8% or 8.28 cm or 8.3 ..sa vcut sir ang formula ntin dito ay tangent..check mo nlang sa iba kung vedeo kung pano gamitin ang formula...

Try mo sa ibang vedeo ko yong paano ang tangang formula ng 45 degree

Example brother 10 cm distance of offset and 10 cm width of cable tray..distance of offset over sin 43.7 degree...10cm distance ÷0.690 sin of 43.7 degree =14.49 this is the travel....for the vcut tangent half of 43.7 is 21.85 degree...so tangent of 21.85 is 0.400....0.400×10 cm width of cable tray =4...so 4 ×2 =8 cm this is the vcut.....for the distance multiplier 14.49÷10 cm distance of offset =1.449 dm...about 4×2=8...4 is the result of half of 43.7 so make times two

Ok brother,i got it.thank's so much.

Thank you po sir

Ok sir..check klang sir ha baka nagkamali ako..ang (sin) ng 40 degree is 0.642 so divide ntin sa 100 ÷ 0.642 =15.57 yan ang travel..1÷ 0.642 =1557 yan ang multiplier..so yong 100 or 1 ito yong common ng formula

Ano bang formula ang gamit mo nyan..sa tangent formula divide lang ntin kung ilang vcut yan ang magiging degree nya..

Check other vedeo have vedeo about formula

13 cm padin less mo..yong 13 cm pang all size nyan ng cable tray..take note yan 13 cm less para lang yan sa 3 cut..

salamat po.god bless

Yes lahat na yan ng size ng cable tray..take note para lang yan sa 45 degree yang less 7cm..

pano nman pag 3 or 4 vcut gamitin mo same pa din po ba 7 cm less

@@Richardcastillano-iw5sn magkaiba sila..sa 3 vcut less 13..sa 4 vcut 20 cm less...yong vcut ntin sa 2 vcut d ntin pwede gamitin sa 3&4 vcut magkakaiba ang vcut nila..

last na tanong nlng po boss pasensya na. pano nman po pag yung travel mo is hindi na 10 cm nag depende nlng sa gusto mo yung 7cm less yun pa din ba gagamitin mo halimbawa nlng 20 cm yung gamitin ko na travel. thank u boss and godbless

@@Richardcastillano-iw5sn halimbawa magbago ka ng travel sample 5cm travel mo multiply molang yong 5x.7 total nyan yan ang less mo..

Philippines (tagalog)

Correct sir..but if directly cm the total the 400 mm converted into the cm.so 400 mm become 40 cm so multiply it in .8 so directly the total is 32 cm.

Ok sir thank you so much. Keep it up sir to educating with your knowledge and experience 👍👍👍

Yes sir.same formula horizontal or vertical

​@@rollydiaz5046that is tray 300mm x 100mm. Vertical offset : tan 15° x 300 (300 is bottom of tray or width of tray) Horizontal offset : tan 15° x 100 (side tray or height tray) or still multiply by 300 sir? Thanks a lot sir

Horizontal offset yang sample sir..bottom ng cble tray or width yong nka vcut..pag vertical offset yong side or thickness yong nka vcut sir..

@@rollydiaz5046 Ok thanks a lot sir..very helpful 👍👍👍

Sample 20 degree..for vcut tangent of 10 degree half of 20 degree..sample tangent 10=0.176..10 cm wedth cable tray multiply by 0.176=1.76 multiply again by 2 hinati kasi ntin yong 20 degree..so 1.76×2=3.52 or 3.5 cm yan ang vcut

May mga vedeo tayo nyan sir kung paano magcalculate ng vcut saka travel..

@@rollydiaz5046 if 35 degree to find vcut : 1. Half of 35 = 17.5 2. Tan 17.5 = 0.3152..... 3. If width of tray 10, so 0.3152 x 10 = 3.152 4. Multiply by 2, so 3.152 x 2 = 6.3 cm Ok thank you sir I forget, this is for vertical or horizontal sir, cz step 3 use width of tray

2cut 24.84 cm bawat vcut travel 10 cm....3cut 16.02 cm bawat vcut travel 10 cm....4cut 11.88 cm bawat vcut travel 10 cm..

Cable tray formula is same also for piping formula

@@rollydiaz5046 ok thanks

@@rollydiaz5046 one question. How to find 45 degree of 1.414.what is farmula

​@@ratneshmaurya5924sine for travel tangent for vcut.sample set or distance 100 mm multiply by 1.414 equal total travel..for vcut 8.28 cm for 100 mm sample of width of cable tray..next vedeo i well make 45 degree offset..

Hindi sir 8.28 both side ang cuting nyan..

​@@rollydiaz5046b22

May formula yan sir may vedeo ako nyan kung paano magcalculate ng vcut saka yong travel nya..

Sin(30)=0.5 100 over 0.5=200mm or 20 cm yan ang formula...yang 20 cm less common nyan sa lahat ng size ng cble...less 20 klang lagi..

Next content ntin paliwanag ko nlang kaibahan ng 2cut 3cut saka 4cut pagdating sa mga less nila..

Sir yong vcut ntin ay nka constant yan sa sample ntin na 10X10 cm na lapad ng cable tray..pero pwede ntin gawing multiplier yan na given ntin na vcut depende sa lapad ng cable tray.result nyan yan na yong vcut ntin sir..

Ok po sir tama po yang nbangit mo ang ginawa kulang kc short kuna para dina sila mahirapan sa computation..nxt vedeo ko sir paliwanag klang kung paano short cut ginawa ko..

Optional lang yong travel sir yong 10 cm common lang ginagamit.pwede ka gumamit ng 5 10 15 or 20 cm..

@@rollydiaz5046 salamat boss

5 cm pala distance non dlawang v cut..

Masking ano laki ng tray 5cm layo bsta 4 cut offset 5cm wala iba sukat dyan 5cm