Видео

Nice

"i'm not gonna stand here and sand the fuck out of it" that's your problem man lol all fiberglass parts need prep work. if you're not willing to bust out the orbital and bondo you're not gonna have a perfect part

The glass on mine will open but the main lift gate stays shut I pull the handle from outside up and it won’t budge as if though it’s still locked

This guy does not know what he is talking about 🤦‍♂️

Good stuff I use 3 light coats with a horse hair brush & don't polish or sand the last coat turns out like glass every time. IF you have to wet sand after the 2nd coat dries with 1000 grit 3M paper.

put a new spark plug to get my 128ld up and running for this year and it worked great yesterday. 2 pulls to start it, perfect idle, no stalling on high revs, great. today, it won't even begin to start. absolutely mind boggled.

Will an 02 SS front end fit on a 97 camero z28?

Seems like it would be a lot easier if he pulled on there forward and reversed out? He'd already be lined up straight when he had to take it off. But he did great being it's his first time!

Wait so I can just take the plastic cover off and hit it with my finger manually? And it’ll unlock?

Did you lose any power with the big wheels? Just got the same setup with only a 2inch lift. Haven't put them on yet💪🏾

Gonna sell the car at night... one of those guys nice...

Did they end up leaking ?

if when sanding it and then polishing it you can still see sanding marks .... maybe a finer sand paper is the way to go ? what i mean is if it is not sand down wouldn't it leave a un flat surface with waves for exemple???

I have that problem now , Got a used latch asm for 25 from the junk yard , If you got a key hole you have to replace it with one ,Theres a sensor plug on key hole lock models only ,, I got mine rekeyed at the locksmith for 30

Great videos and I love the cussing lmmfao it just makes the video that much better!

Could a 2014 do this? Looking at one

Would have been helpful had you shown how you set the timing. I have the same issue with a weed wacker. Guess that is the problem, have checked everything else, have new plug, good spark, new carb, 75 psi compression.

Has anyone done the 93-97 front end swap to ls1?? I think i want to do it..

SMH 🤦‍♂️ bruh bought a skid steer n don’t even kno the basics to putting a rock behind the tire. And make sure those ramps are all the way down. Rookie

8 dollars a dg today go online get it

I don't feel bad, if you can't anticipate how trash the quality is prior to ordering it by doing 5 minutes of research then thats on you

Put bucket down and turn down the throttle holy shi

Can you put number part

Buddy you saved my ass, thank you for the video

Sounds like a good way to go at least time and aggravation wise,would be to find a cheap 6 cly model in good shape and you'd have all your front end parts,minus SS hood of course.Lot of work though,nice job!

Thanks for not showing us anything

Hey man I really appreciate it my caliber piston shot through my break bad and hit the rotor I would still be there If it wasn’t for you all the other videos on this project where very poor examples thanks again.

thank you that was dope. nice video

I ain’t gone lie I just got a bumper from durflex that Shìt is so trash bro

What about dip stick tube issues

So how do you adjust the timing? I see no way. And you didn’t explain the fix? Or I missed it each time I’ve watched. Timing doesn’t change unless you took it all apart and put it back wrong. You would have had to remove the flywheel and put it in completely out 90 degrees. With a keyed drive shaft there is no way to get it wrong unless their are double jetway where it could be possible to get it upside down.

Technically it’s a compact tracked loader

good video man im putting the same on my 95 right now got the drivers side on what did ya do with the steering shaft i had to take it off to get the header in but now the shaft hits the tube

Glad I watched this before I tackled the job. I got the same headers. Really didnt want to remove the starter. Cheers!

Hope you had luck finding that gal. I am turning 55 in a month and never found the right woman. Beginning to think they do not exist. If a good looking guy like you cannot find one we are finished.

Where can you find this product? I can only find warm gloss not clear glosss at lowes

How did they seal? Thinking of doing this myself

I have a Ryobi hedge trimmer that the flywheel will spin out of position and loses timing..there’s no key way…the flywheel basically supposedly stays in place just by being held on crankshaft by compression of the clutch…terrible design.

Is it me or is that bucket upside down

Put somethin under the wheels so ur trailer isn’t dancing around next time Also might wanna learn how to put Ramps down

Zero issues after watching this, mine works perfectly ruclips.net/video/IXqmhZ4VLVc/видео.html

Good job.. But I prefer the 93-97 look. Catfish look is too bubbly😊

do you think itd be possible to do the same w a firebird front end and perrhaps fenders? always loved the camaro rear and firebird front

same problem with my hood, its insane

I like your style bud just Keep fuccing shit up like I smiled because u make it seems like no big deal

Thats kinda ofenceive to others ngl

Fantastic job! I've never had a problem with Minwax. Thanks for posting. 👍

Мили!? Хуили! В Америку езжай у них мили

X5M👍👌❤

Thanks for the video. So basically, no final sanding and you just went straight to polish?