Видео

I made it go vibrato meaning only the pitch modulation comes out of output A when the pedal detects output B is plugged in. The boss ce3 gave you the option for classic stereo chorus (wet dry) and inverted stereo for true stereo but you could choose what stereo option using the rotary switch on the ce3 On the ch1 the output jacks work like switch’s telling the pedal wether to send mono or stereo. But using chorus with only 100% wet vs dry gives you vibrato.

Thanks! I very much appreciate that!

That creates a popping noise similar to your output Jack being unplugged every time you switch it while the guitar is played through a clean di.

Thanks you rock as well!

You would get the same thing with a ts808 or ts9 in front of the ce2w . This is why, the ce2 and many chorus pedals use a buffer that has more going on. With pre emphasis and de emphasis stages that load down and make up your wet signal create a volume boost in the mids around 600 hz this is the sweet ball park of running a tube screamer that has a big mid hump and good enough transparency ( like a ts9 with the gain knob rolled off) An eq pedal before a ce2w would do the trick too. Not only for more ce2 vintage sounds where you can roll off some highs and boost the mids a tad. But you can use an eq pedal plugged into the stereo (wet) out of the ce2w and use the eq to make a hi fi chorus or lofi chorus. The best thing about the ce2w is the Ce1 sound that’s all I’ll say.

sorry but where do you hear the volume drop in the Ce-2waza? Maybe you have audio problems from your PC or phone. The ce-2 waza has a significant INCREASE in volume, which is barely noticeable in the original ce-2. Then I wanted to tell the author of this video that boss has not always used the mn3007 chip for the ce-2. The latest productions, especially those made in Taiwan, used the mn3207 chip.

I wonder if the fuzz pedal they make has a trimpot that turns the effect into a tremolo lol who knows buy one for yourself and have fun

I could but its funnier to watch you do videos on the cheap pedals also can you show me the wiring for a hm-2 by boss i have a circuit that's has messed up wiring and stuff and i need to solder the out put or input back on as its missing one of those 2 i cant tell and how to repair 2 of the pots

sounds fine to me

@@user-kx2uz6vo9g Listen again with headphones. Hard to miss. Most obvious when he's talking close to the mic, and the compressor drops the voice way too much.

I’m gonna talk through a soda can for superb popping effect

Thanks for your suggestion! Keep on rocking!!

Thanks for your consideration but the man upstairs is correct

You got that right

Yes you would hoodwink the audience

Not too sure ngl just turn it counter clockwise until you have a tremolo effect that’s a smidge under unity gain just like a boss tr2

​@@Pedalheadshow Thanks for replying! I had a eureka/duh moment when I remembered I had an old looper I could put before it and just focus on adjusting instead of juggling 😅

NM. Looks like I did this mod at some point and totally forgot I had done it. Geesh!

You gotta know what it feels like to know what it means

This comment blew my mind and made me throw my bass guitar. Thankyou 😎

As useful as a can opener when you buy a fresh can of spam. I’m gonna let that resonate with you.

You got that right. The ce2w uses the mn3207 bbd chip known for the noisy ce3, bf2 and vb2 it is a 1024 stage bbd like the ce2’s mn3007. Except the mn3207 can manage lower Ms of delay to give you the faux ce1 512 stage bbd sound. The ce2 is great for classic sounds but lacks in its transparency to other chorus pedals or rack effects. Some would say the ce2 has a bit of a mid hump. But the ce2 also has a small impedance issue of rolling off high end. The ce2w doesn’t do that in either mode. But tbh they should have just released the waza chorus as a ce-3w because it’s more exact to that circuit. lol

boss has not always used the mn3007 chip for the ce-2. The latest productions, especially those made in Taiwan they used the mn3207 chip.

I tested 12v, 9v dc adapters And battery. There was better response but still a lack of feedback repeats. That made the intensity knob unusable. Especially after listening to other sound demos of the dm-2.

On top works good just make sure you have a good strong connection and a good helping hand of solder.

No it’s called sweetened tuning. Like a chorus pedal. Guitar is an instrument of imperfections.. well at least a Gibson Les Paul is.. 😂 thanks for the tip Gabe, this was a video I made a long time ago. And a Les Paul sucks for tuning stability but I could have done a better job. If I tuned the guitar would that have satisfied your every need want and desire for this video. Gabe, you are my only hope at helping me run a successfully random RUclips channel that guitarists 30+ seem to dig. How can I be relevant in society if I can’t tune my guitar for a RUclips channel for people to see and hear… but most important they must see with their ears. So I guess tuning to 440 Hz and running antares auto tune on my guitar track but that might pose an issue causing the guitar to break in half or something.. anyways Gabe , A+ feedback i do check my tuning every chance i get to where i feel it’s necessary. I’ll admit it I run my guitar and my dialog in every video through auto tune because I don’t want to hurt feelings or hurt the image of the idea Im trying to have listener ya know, see with their ears n what not. Anywho any feedback is greatly appreciated, Gabe. Cause my videos need a professional touch and that what i think your comment resonated in me

@@Pedalheadshow PedalHeadShow when the addi coin lands on PedalTailShow

It’s an on off on switch Middle lug of the switch goes to one point of the capacitor doesn’t matter what side. Then the 2 capacitor values I believe it was .1uf and .022 uf Go to each of the other two lugs right and left of the middle lug of the switch. Those two capacitors are twisted together and soldered together. Then that conjunction gets soldered to a wire that goes to the other corresponding side of the capacitor on the board.

@@Pedalheadshow thank you! I'll give it a try

Yes you are correct that would be a cleaner connection, the same as a diode swap switch on a distortion/OD pedal, except switching between two resistors. Gotcha

Enjoy yourself an awesome guitar!

Yes

@@Pedalheadshow I ran at custom shop PRS into a hand wired fender tremolux Zero distortion then I ran it through my Divided by 13 JRT 9/15 head and cab Zero distortion. Sent it back

Boss super chorus is great! In my opinion the berinnger will get you places, but it’s pales in comparison to the super chorus especially an analog pre 2001 super chorus. The stereo effect on the behrinnger didn’t fully mix out dry from wet. The eq was terrible, the buffer is worse. The yellow is hideous. The boss Super Chorus is the 4th best Boss Chorus , and the 2nd best stereo Chorus in my honest opinion. The best stereo Chorus that boss offers is the Boss Ce-2w Fresh, yet vintage tones. For mono chorus any will do. But the Boss Ch-1 is best for both due to its level control, eq, wet dry routing , and better buffer than the Ce2 and more headroom then the terrible Ce5

Theoretically you could be right. From personal experience it increased touch response , increased high end, brought more headroom to these compressed pups, and increased the overall output. Maybe it’s how fast each battery type could deliver voltage, maybe it’s in the 24 volts, maybe it’s magic, but tbh. Any passive pickups with stacked overdrives/boosts sound and feel way better.

Anytime ! I suggest tinkering with an over drive or distortion pedal like a boss ds1 or an Ibanez ts9, easy mods less likely to run into issues. Have fun!

You’re right ! Gotta love the flange

Try this Gain 3 o clock Channel volume 5 o clock Bass Around 11 o’clock to 1 oclock Mids Boost all the way up Treble 11 o’clock to 1 o clock Probably use the amber metal setting Make sure that your effects are in the proper order I recommend downloading the line 6 bogner editing software from line 6 also make sure yours is up to date and isn’t in need of a firm ware update

@@Pedalheadshow how do i connect it to a pc? And how do i update it

Nice

It’s difficult to hear until you do it yourself

@@Pedalheadshow thanks, I just ordered the mod so will check it out

Glad it worked for you ! 👍

Do this mod or swap out the diode and resistor for jumpers. Then you can run your hm2 on 9v DC

R2 D1

Use the old legs of a resistor for your jumpers

You could do it but you couldn’t switch back to stock. You might need to make your own clone and add a second jrc4558d to the out put like a Ibanez SC10. You can look at the boss Ch-1 schematic for some ideas maybe. I would put a 50k pot at R22 or R24 for giving you a blend for the chorus effect but I think that could effect the out put signal when the pedal is in bypass . then again.. you can look at the boss Ce2 and ce2b Schematics because that has a mix knob But to run in parallel means dry and wet effect blended together. So to answer your question. Get an fx loop pedal Clip offR21 Only gives you the wet signal of the ce-2 (triangle Vibrato) then use that effect with the check light always on. Because you kill your dry bypass signal. That’s why you use a fx loop pedal

Then use that in conjunction with a clean signal. Thus giving you a parallel effect. This may or may not introduce clock noise im pretty sure it shouldn’t but remember you don’t have your usual ce2 you only have the wet so you can only have the effect on, so use a fx loop pedal or as I use an effect loop block in the helix that gives me send return and mix level for any separate unit I want to use with the helix.

I’ll do this for a video might as well do a quick mod for the fun of it.

Yup that would be much help jk

Yeah.

Emgs are great! I recommend swapping out the pcb board for real pots and capacitors, then you’re pickups won’t be hindered.

@@Pedalheadshow Thank you！

That’s good we’re all enjoying our $1500.00 chibsons aren’t we?

@@Pedalheadshow at this point Gibson themselves are making the chibsons lmfao. But you're damn right!!

Not often just make sure you unplug your guitar when you’re done playing. That way you can preserve your battery life. I usually switch them out every 2 months.

@@Pedalheadshow Ok, great! Thanks🤘

Can’t. The boss metal core is digital. Thanks for the suggestion though

Thanks for that. I shall in the future thanks for the recommendation. :)

555 is an angel number meaning change. And 11/10 is an important day to me and my wife. 2024 is the year I built this pedal . Why do you ask?

I have your Pedal! I was just curious about the numbers and the 11/10 was close to the #555, Thank you for the details!@@Pedalheadshow -Cheers! 🥃

Enjoy it my friend!