Видео

Ok so everything worked with the control panel. But when I open flight simulator 2024, the flight stick is there but there is NO default settings whatsoever. So it is basically empty. How do bypass that? It is registered in the game but without any settings.... pls help. or send me a video of how to set up all the controls manually.. thx <3

SIR I HAVE ENCOUNTERED AND ERROR IN THE CONNECTION OF THE AKK X2 VTX AND SPEEDYBEE F4V3 WHEN I TRY TO CHECK THE CAMERA FEED THEN ONLY THE GREY SCREEN WITH OSD DISPLAY BUT WHEN I TRY TO REPLUG THE CAMERA WIRE AGAIN THEN THE CAMERA FEED WAS OK BUT THERE WAS NO OSD PLS HELP ME SIR . I HAVE ATTACHED THE PROBLEM VIDEO LINK drive.google.com/file/d/1lx82GscG2kU3wUGcPbxqn5JZJsMNwb1J/view?usp=sharing

I need help with channel trim in T10 help me please.

How is the range and video on the t10?

Thanks saved me from buying a new one

How is video and range with this transmitter?

My throttle and rudder dosent work... This shit work in the R2 and L2 botton

Hope you are all safe Prayers from Australia 🇦🇺

Thank you my friend ❤❤😅

Hi, can you please help me with trimming my drone controls, I dont know how to do it with skydroid t12. My drone controls are out of tune. Please help, this is for my school project

I just bought for PC, will it work with msfs2020?

Is it still compatible with new windows (windows 11)?

sir i have problem . the drone is flying in manual mode also shaking and in gps mode it is not even arming sir it is fliping pls help me with this same dji naza m lite

Lost the packaging for mine years ago and havent set it up since i factory reset my computer. Didnt remember they dont include the PC drivers by default. Thank you for the video man.

Hello, everybody. I want to connect an MG996R servo to the Pixhawk 2.4.8 autopilot without interference from the remote control, to achieve continuous angular movement of 10 degrees right and 10 degrees left. I have powered the servo from the BEC of the ESC, and the PWM signal is sent from AUX1. I am able to move the servo through Mission Planner using the Servo Output tab by adjusting the SERVOn_MAX, SERVOn_MIN, or SERVOn_TRIM values, but I cannot achieve continuous movement. Is using a Lua script the only solution?

thank you!! 😀

Thank you, that was helpful .

Still did not work and wasted a lot of time DJI is dead

Thank you🙏

bro, from Sardinia, Italy, thanks a lot.

Mines just flashing red and green. Tried to power it 6 times but does not blink green. Only blinks green and red

Thank you 👏👏

After I calibrate my esc's they give out 3 beeps and a long beep after that it starts single beeping again wtf ? Any help ?

I can't get the settings test screen to come up on my pc! Any help please

The easy way "plugs into usb"

I got no binding and try every way, do you know what's problem

Ты молодец,дружище! Спасибо!!!

it didn't work

???????????????????????

Nice vid but my timer dosent stop with throttle back to 0 Pls help

00:42 remote control or remote kon+0l..?...

Bluetooth not showing in pc do you have solution for that

IMPORTANT!!!!! MAKE SURE THE SWITCH ON THE BASE OF THE THROTTLE IS SWITCHED ON TO PC!!!! I was bashing my head in trying to figure this out and turns out I didn’t have the switch on MAKE SURE ITS ON!!!!!!

I would love to know what all the changes you made to your swellpro and why did you change the flight controller

You're also the only one who made a video that explained why it wasn't working

Thank you so much i got mine for christmas and haven't been able to use it until now

I will make my comment here, because this is the first video that I watched on my problem) Make sure that your RX connected to Pixhawk receives a signal from TX in MissionPlaner: SETUP - Mandatory Hardware - Radio Calibration after that, put BRD_SAFETY_DEFLT=0 in config (I understand that this is a newer name in new versions of MissionPlaner for BRD_SAFETYENABLE) and MOT_SAFE_DISARM=0. Next, go to SETUP - Mandatory Hardware - Servo Output and select the function for your devices, my motors were in the first positions.. i.e. 1,2,3,4. First I chose the Motor1, Motor2 function.. (how many motors do you have) and went to the SETUP - Mandatory Hardware - Motor Test. And I was checking like a melody if you click on the test (I have pixhawk 2.4.8 and FS-iA6B). Next, I connected the battery and this test worked and the motors began to rotate. You can either perform ESC calibration before or after the last point. I don't quite remember the order. But if you select the Motor1 function, then the motors will work as if in a program, and not with TX. To control them with TX, set the RCIN# function (# = the channel number for throttle). In this configuration, the motors operate from the TX. But I'll have to figure out how to change it automatically and so on. At first, to avoid beeps, it works.

ooh way thats grate! One thing keeps me thinking. Is it only the software or is the hardware sensors inside the V2 better? Because the orriginal v2 is way more stabel thamn the v1, i saw in a video

How many km run this transmetter use

Where is the link ???

Thanx. This helped me a lot🤠👍🛩️🇿🇦

You saved my money .... Before throwing into garbage 😅.... Thanks a lot ✨🤩🤩

thank you so much sir

Thank you so much, man! Easy, clear instructions got my retracts working! Never set up such things before, lol.

Thank you my friend that helped me a lot 👍

Best video on easy way to setup a timer. Thanks! (It is well worth the sub!) Telling all my buds.

Hello! Great content, I enjoy your videos. I was wondering if you could do a video on how to control a drone / rover remotly over IoT? As is over 4G/5G cellular signal?

באיזה אזור אתה מטיס

Just bind both at the same time. Only issue I have is that only on of my drones gives me telemetery!

not working for my still the same problem en i dont see the green menu