Видео

@@rodnietorres3082 1, doesn’t matter what side

@@rickytube2375 appreciate it. How long have you been running it like that and has the check engine ever turned back on?

@@rodnietorres3082 around 1 year, no light never came on.

@@rickytube2375 my bad but I have one more question. You used the 90 degree filter but is the one that just goes straight fine? I bought the berk resonated test pipes and it already has an extensions welded on but people say the light still turns on so I was going to be the regular straight ones since they where 5 dollars at Walmart.

@@rodnietorres3082 I couldn’t tell you ive always ran the 90 degree one. Im sure it would work

@@franciscoserrano9045 they should be linked in the description of the vid

@@joshuakrall4865 linked in the description

@@rickytube2375it’s not there

It’s there if you click see more, I copied the link from there. www.autozone.com/a-c-charging-and-refrigerant/a-c-oil/p/a-c-certified-pro-r134a-pag-46-refrigerant-oil-with-ice-32-8oz/70570_0_0

No mine didn’t make noise. you can adjust the front while they’re on the car, but you gotta take off the back coils to be able to adjust them

@@rickytube2375 you mean to adjust the dampening ik you gotta take off the rear but i mean the ride height because i wanna raise the rear a little bit can i do it while its on the car or gotta take em off

@@IvanV36 oh yeah my fault I miss read that. Yes, you can lower and raise your coils while they’re installed on the car

Not a direct fit, you’ll need to do some minor things to make it fit. It also depends on the size of the oil cooler

just do a regular oil change, it's just like the engine most of it will come out and a little will always sit in there. Just don't wait to long to change your oil.

nope

Need toe arms

@@CharlieOAM someone on insta with the rev9 coils said I can just take out the coil spring and leave the bucket empty which is probably what I’ll do

I’m not to sure. You can see on z1 if it fits the x model

No

@@rickytube2375 gotcha so i ordered the same ones you got where will i be able to get the correct ones or you don’t need them ?

@@angelrosario1813 you technically don’t need it. I only put it on so the check engine light wouldn’t come on

@@rickytube2375 gotcha yeah i was trying to look for the ones u got but i can’t find it mind sharing the ones you got or one that would work too thank you

@@angelrosario1813 I honestly don’t know which one I got. Anyone will do, I think I got mine off of ebay

at like 6:50

No

I didn’t it, they didn’t come on my car

No

No I didn’t have to trim down original studs

19x9.5 fronts and 19x10.5 rears 255/35 tire all around

those are 19s, the nismo v1 from a 370z

Wasn’t my car. I wouldn’t recommend god speeds, I would definitely go with some bc’s or teins

Only if you buy the spacers that don’t come with studs on it

@@rickytube2375 I got the z1 20 mm so they should go on good? I’m ready to get these on 🤣 jus Hopin my studs are long enough

@@austinturner7071 yeah I bought the same ones from z1.

255/35

Tunerzstore.com is where I bought mine

No there’s no other way for the rear unless you you drill through your chassis but I wouldn’t recommend that

The ones I got you just need to remove the wheel and reach up where the two 12mm bolts are, they changed their design.

The bracket stays on there but you should be able to loosen it with a allen key and move it up and down. The brake lines that are connected to the bracket can easily pop off with your hand

I’m talking about the black part that moves up and down how do you remove that

@@AyoubAbubaoer it’s not supposed to be removed unless you cut it off

The brakes lines just pop off. The bracket isn’t meant to be taken off unless you just cut it off

So what you can like adjust it when I try to adjus mine it jus stays still it doesn’t move

@@AyoubAbubaoer spray some pb blaster on it and see if it that works. It might be seized unless you maxed out your threads

Nismos v1

19x9.5 fronts and 19x10.5 rears

Y-pipe

2

On god 😂

I bought them off of someone. You can buy them brand new from z1 but they’re really expensive. I’m running a staggered set up, 9.5 in the front and 10.5 in the back with 255/35 tires all around

No I don’t, I was going to a upload on that later down the line

@@rickytube2375 👍🏾

Not with my exhaust, but it depends what exhaust you run.

@@rickytube2375 am running a invidia exhaust, am trying to decide whether resonated or non resonated berks tp for best performance and sound, any recommendations

@@rickytube2375 hey bro does it have a deep sound or thin sound

@@torvarrisevans7846 my exhaust set up isn’t to deep. I’m planning on switching it up really soon. If you want a louder exhaust then I would go non resonated, but if you don’t want any rasp at all then go resonated. They both give you the same performance once tuned. Depending on what invida exhaust will also play into how deep or raspy your car is.

@@rickytube2375 thank u bro

My gaskets are still good, but I’ve only put down around 4k miles on them