- Видео 23
- Просмотров 11 235
A M
Добавлен 10 окт 2012
Vermillion Ohio Northern Lights 4K
Oct 10 '24 Northern Lights with a KP8.3. Set the GoPro 10 up with 20sec intervals and Auto shutter and let it run from 8pm till the sun came up. The glow on the left side is Cedar Point.
Просмотров: 42
Видео
Cz60r L2.3
Просмотров 74 месяца назад
Just documenting error for dealer. Error occurred 20min into moving high blade speed high drive speed with deck at 3.75”. Error L2.5 was what originally stopped the blades (forgot to record). Turned key off then on and error went away (like yesterday) and cut for another 20’. I turned blades off to pick up a stick and error L2.3 came on and now won’t turn blades on. 8/28/24
Cz60r cut quality after error
Просмотров 104 месяца назад
Might be tricky to tell, but after error L2.5, this is the cut quality. I suspect an issue with left spindle motor (original assumption). After I cut for a few minutes, error L2.3 happened and blades won’t start back up.
Cz60r error
Просмотров 64 месяца назад
Mower stopped dead so I went and grabbed my phone to record if anything reset when I turned key off. I’ve been having error L2.3 pop up every now and again, this is the first for the next errors. Original error was L2.5, turned key off and waited and then all these errors popped up. Even the next morning, same errors. I tried unhooking the main battery cables for an hr and that don’t change.
Northern Lights '24
Просмотров 47 месяцев назад
Northern Lights in Vermillion Ohio 5/10/24. Had long exposure setup to get the vivid colors. 10pm-11pm local
Easy Bend Line Set Bender demo with insulation removed.
Просмотров 9 тыс.2 года назад
Working on installing my own multiple zone mini split system and wanted to make clean and kink free bends. No one has a video of the line set without the insulation after they did a bend, so I have extra line to try it on first.
Teal Bird 1961 Penfound Design
Просмотров 113 года назад
1961 Thunderbird redesigned by Penfound Design into TealBird
Penfound Design 1961 Teal Bird
Просмотров 603 года назад
1961 Thunderbird transformed by Penfound Design into TealBird
‘14 CTS-v Idle with stock muffler, SW headers and and tubes with no Cat.
Просмотров 6914 года назад
Upper pulley, air intake, tune and stainless works headers with no cat to stock muffler.
Penfound Design's 1959 Buick LoSabre
Просмотров 7754 года назад
1959 Buick LoSabre from Penfound Design
I visited Vermillion 1 months ago ....I have seen northern lights.... Beautiful !
Can you give a link to the amazon page?
@@ponetwozerodrone3707 never been able to find it on Amazon. Had to buy it through other means. I think eBay, but don’t recall.
Ive heard that your success improves if you over bend slightly then back off which will release the insert.
I don’t think you could pull that out if you made more than one bend in it.
@@TheRemyRomano correct. About 2 bends or one tight bend. And if you were in a tight location (attic) would make it even more difficult. I had the opportunity to be doing the bends in the open and 1 at a time.
Como eu posso comprar?
I bought it off amazon.
Isn't there a way to temporarily peel back the insulation and use a tubing bender tool? I don't install mini splits but at my work I had to build a small module to regulate nitrogen with different gauges and I was using 1/4 stainless steel tubing in which I had to make the tightest bends possible with the bending tool and then install the connectors and flare the ends, so long story short, if you need to make a tight smooth un-kinked bend, it seems to me a bending tool would be best, again, I don't do mini's but it is in my plan to install a couple soon, and I'm thinking of hiding the lines in the wall and it's going to require tight bends. Sorry for being long winded🍻
So this is what I do for a few parts where I had access to do so. I cut the insulation, made the bend with the tubing bender and then reinstall the insulation. Other sections, I didn't have the room to remove the insulation to do so or the room to use a hand bender.
Como puedo adquirir este producto me encuentro en colombia
Found it on Amazon
Horrible product if you're trying to bend long lengths because after the line set is bent you cannot get the bender out!
I didn’t do more than one tight bend. I did a few slight bends with one run. Yes it is hard to pull out if you did a tight bend and would be difficult if you were in a tight place (attic) and trying to pull this out
According to the manufacturer, you are supposed to pull the bender out as you make your bends. ruclips.net/video/uQFMcuMOK9A/видео.htmlsi=Gj9tiDPM0fQ5AdWD
yes plus I rarely see the need to stick it in more than 4 feet or so most of your bending is going to be within a few feet of the indoor/outdoor unit. However if you do have a bend such as where it exits the exterior wall and it not a wall hung unit. make the farthest bend first and then pull it out past that bend before making the next bend this way you are only fighting the friction of one bend at a time. if you make a pretzel and then try to remove all at once....good luck @@Aspen5.7
Nice, thanks. I wish it was more affordable, I need it for one time to do hard 90 bend for 1/2 inch for mini split. Hoping to find PEX that fits inside the 1/2.
That’s exactly what I needed it for too. I used it everywhere I had a bend just because I had it. Main reason I bought was to make hard 90 out of the unit and go up into the attic and stay in the confines of the 2x4 wall.
Did you find pex that worked internally with 1/2"?
@@anthonymiller3933 I got 1/4 inch piece of pex of about 4 or 6 ft at Home Depot for under $5 but It didn't work for me, it was to soft and copper pipe kinked, so I just returned. I ended up paying an HVAC technician to install the line set and do the 3 x 90 degree sharp bending with his bending tool.
@@joaquinsuarez6090you should have tried to fill up that pex with sand
@@andreycham4797 I found a 4 ft piece or 1/4 at Home Depot that fitted inside the 1/2 copper pipe but it didn't work and kinked. I think it was to soft?
Unique in all the world!
How was the figment on the headers
FIRST COMMENT!!!!!!!!
And second
Just wanted to be your first comment