![Mainly electrical](/img/default-banner.jpg)
- Видео 2 333
- Просмотров 7 573 778
Mainly electrical
Добавлен 24 май 2014
UK 🇬🇧 electrician . Welcome to my channel, an educational experience. Join this channel to learn
ruclips.net/channel/UC4bzmBgEUo4fLy3F9q8KhnAjoin
ruclips.net/channel/UC4bzmBgEUo4fLy3F9q8KhnAjoin
Видео
What's the earthing arrangement ?
Просмотров 7504 часа назад
NEST THERMOSTATS ☎️
Просмотров 3306 часов назад
Ooooh Fire Hazard !!! 🔥
Просмотров 5446 часов назад
Oooh a Short Circuit !!! 🥰
Просмотров 6177 часов назад
Mainly Everything Trips it !!! ☎️
Просмотров 2,9 тыс.День назад
7 amps on the sheath .. potential issue ???
Просмотров 1,6 тыс.День назад
Tripping a type A Rcd ??? 🧐
Просмотров 1 тыс.День назад
Ooooh Close Call !!! ☠️
Просмотров 1,8 тыс.2 дня назад
Boys it's Plastic Ffs !!! ☠️
Просмотров 1,6 тыс.2 дня назад
No trip at 30mA !!! ☠️
Просмотров 1,1 тыс.2 дня назад
Touch Voltage !!! ⚡️☠️
Просмотров 3,8 тыс.3 дня назад
Get it swapped ASAAAPPPP !!! ☎️
Просмотров 4,6 тыс.3 дня назад
Loose Connection Sir !!! 🧐
Просмотров 2,4 тыс.3 дня назад
Sunday call outs !! Round 5 !! ☎️
Просмотров 2,4 тыс.4 дня назад
Lim as we not allowed to open it and check it apparently 😂😂😂
Measure it 👍
What do they have on the lighting circuit pulling 8.6A!? ANd what's that chonk meister 63A circuit feeding?
OCPD is over current goes through that device 👍
TNCS
Yes is thermal heat in the main switch 👍
Looks like TNS but i think I would test just to make sure
Over cooking! Sometimes the most obvious is over looked.
I have seen many certificates and eicr certs where the spart has put these tns cut outs down as tnc-s
I don’t know why some of saying Tns when is not, it is TNCS
It looks like pme but I would bet its tns
tncs
I’d once have assumed TN-C-S unless the test results proved otherwise, now I’d be a little more circumspect. It still depends on the numbers, and most likely it was TN-S once if it isn’t still.
A bit too much juice for that breaker
TNCS
N swapping
TNCS
TNS. If you break the cut out apart,.you can see the sweated link off the lead!
Never assume, in my experience, that could be TN-S or a link is in it to make it TN-C-S. If the MET is exposed from the head, then more than likely, it was a TN-S at some point. If we test, then we will find out.
Tns unless theres a pme label
Main switch needs replacing.
Tncs
Many would .. it's actually TNS
Tbh, you just spoke Chinese to me then…😅 I am illeterate with hearing systems. But you have inspired me to book a 1 day course to get my head around it! So keep it up, it’s great stuff! 👍👍 Thanks
WhatsApp with any questions 👌
Main switch still on the on position
Why do european switch boards work from right to left?
They can go right to left or left to right although right to left is more common. Mostly dictated by preference and incoming supply access.
Coz , we have to be different 😊
I be think this is short circuit happen 👍
I’d say the circuits have the neutrals running from the wrong RCDs
I like the time delay beside the meter and the Robo’s down stream
Type AC
😂❤
Let's goooo T 💪😎❤️
Newcomer to the industry. What is the process for proven imported neutral fault current. Is it DNO?
But it's good practice 😂😂😂
Change, peace of mind for you & the client. 😊
Never seen that before, how does it even stay on after a reset
Why does the near side mcb trip the far side RCD. I get why the far side RCD trips when MCB up as NE fault. Cannot really see, are the neutral bars correctly done
Happy if you stick the explanation up in members
Morning Bri .. I'll put it on a member only today .. . We also need the to speak about the shower incident 👌
Yes
Borrowed neutral 😅
This appears to be starting to fail replacement may be needed or it could be checked again at a later date to see if it’s getting worse. It really depends however I would guess it would probably be type ac as they have to be quite old to start drifting so it probably would need replacement anyway
I don’t know if it’s just me but the gas looks like at the bottom that it is copper but has been covered in plastic but putting a bond on a plastic pipe is not the worst idea. It’s unlikely Pacific was to ever be replaced for metal is already there and secured, so it doesn’t get cut off by people thinking it’s not necessary.
Great work by the decorator....! 😂😂😂