Видео

it's 8.5v not charging

i don't know, but you have to check the battery as well, as it behaves like that when it is faulty

@@apsubmittedtoGod isolved the problem tnk u btu triac is faulty 1and 3 pin is shorted is fix it now charger is working now

@@ksklee74 👍

does it charge the battery?

@@apsubmittedtoGod Igen tölti

@@istvanszilagyi5773 check buzzer, the round component marked with 2202, at minute 18:05

@@istvanszilagyi5773 or try this ruclips.net/video/ORYGCT5Oc0A/видео.html

@@apsubmittedtoGod igen

no, just te 76 old model

@@user-ju3et8gg5j yes

Making it free volt will make it not very efficient, as for lower voltage it requires a bigger capacitor and taking so twice the space, it is just one capacitor to be changed and you either have it 230 or 120v. In this case it works with 230v but also less effectively with half the power in 120v

@@mujahid-salim hello, how can i help you?

@@orinokoflow6280 i dont know, it can be anything, you have to check all the way in of the power from the battery, but the thing with the power button is a common problem for Hilti, the flexible conmectors sometimes disconnect in the middle.

P6NK90Z, but you can use higher amperage, i usually put P10NK90z

diodes 1N4007

@@apsubmittedtoGod Many thanks !👍

just google AL 1860 schematic and select images, someone has posted it

what is the problem with DD250?

just change the big capacitor to 400-450volts and with half uF value, and remove any varistor that is in parallel before the bridge rectifier

You also have to check nearby resistors and diodes, because when a transistor gets shorted in gate pin, it may damage components or even the IC,

@@MihaiAlexandruPreda no, it works just for TE76 old model

@@apsubmittedtoGod thank you.

ruclips.net/video/vWcRAZqbukw/видео.html Replace the capacitor from 220v to 400-450v, and remove the varistor, the yellow component

180k ohm

@@HardcoreHokage the Creator and Owner of everything, the Book of good moral values. God bless you.

@@apsubmittedtoGod ah your talking about Zeus. Where can I get a copy of Zeus' holy book?

@@HardcoreHokage zeus was the son of cronus, he wasnt the creator of the universe

@@apsubmittedtoGod No it was Uranus who created the Universe. Zeus bless you.

@@HardcoreHokage uranus still had parents, so not the God the Creator and Owner of everything

Exactly the D3 and R7

@@uncanalmas5824 no, i didn't, D3, R7 and the capacitor there are snubber circuit to block voltage spikes coming from transformer, 1:43

do the LEDs turn on when you plug it in?

@@apsubmittedtoGod no. Nothing happend. Only appear 165 VDC in the mains capacitors.

@@carlosreyes-ko9im so the problem is in the snubber circuit, is it the same exact charger as this in the video?

@@apsubmittedtoGod HI thanks for answer. Modelo charger is DC18RA

@@carlosreyes-ko9im did you find any faulty component there?

these chargers after conversion work fine, no problems with that

no, it works only with this tool TE76P ATC

are you sure the batteries are ok?, if yes, then check the mosfet, the big capacitor, and small capacitor near the driving IC

@@apsubmittedtoGod Ok. Thx. Picture of the driving IC? Regards

@@user-2uf2kr2c 13:13 IC1 the one with 8 pins, and capacitor C12

@@apsubmittedtoGod Ok thx. Godbless

Hello. Mine stand by voltaje. K3113 is ok, but dont have 5 volts. Do you know what cold be?

you need SRT service reset tool, to do that

this is a common issue if the battery is faulty, not the charger

@@apsubmittedtoGod thank you so much for replying. This shows your dedication to your subscribers..

not the golden ones, just the small torx screw that is accessible by just removing the protecting glass

What size torx screws are they? Thank you sooo much for this video. Now I don’t have to send this damn thing out for service! I understood every word you didn’t say!😆

My app says mines outa whack because it got too hot.🥵 have u ever heard of that before? Also, is it normal for horizontal to b outa level but the verticals still ok? Mine is the gll3-330cg, has never been dropped and always been treated nicely. Can I adjust just the horizontal?

T8​@@RubRubTuggington

@@RubRubTuggington yes you can but a little difficult as once you adjust the horizontal the weight if the pendulum will change and the verticals will change too, so you have to keep adjusting until every dimension is ok