E-Scoot & Tech
E-Scoot & Tech
  • Видео 4
  • Просмотров 64 412
Unlock the speed limit on the HERO S8/S9
To unlock the speed limit from the HERO S8 or S9:
1. Before you turn on the scooter, push the throttle (accelerator) until the end (pushing it downwards)
2. Then, without releasing the throttle, turn on the scooter and keep on holding the throttle for 15 seconds
3. After that, the speed limit should be unlocked
WARNING! In some jurisdictions, it might be illegal to roll in public areas without the limit speed and might also constitute a crime. Review your local laws before proceeding to unlock your speed limit.
All activities you perform shall be done under your own risk and responsibility and we shall not be taken accountable for any damages or activities performed based on the content of o...
Просмотров: 61 283

Видео

Unlock the speed limit on the CURRUS NF PLUS/NF10
Просмотров 1,9 тыс.4 года назад
To unlock the speed limit from the CURRUS NF PLUS, you need to open the deck (foot base) with Allen keys 3 mm. Unplug the buckle (Orange cable plugged in the original gray cables' connection). WARNING! In some jurisdictions, it might be illegal to roll in public areas without the limit speed and might also constitute a crime. Review your local laws before proceeding to unlock your speed limit. ...
Pixel 5 Unboxing
Просмотров 304 года назад
Real life unboxing Pixel 5 EU Version

Комментарии

  • @BSDaxer-v4p
    @BSDaxer-v4p Месяц назад

    It’s fake?

  • @kalamaty
    @kalamaty Месяц назад

    Thank you for this tutorial! Definitely going to try, since my NF Plus is only topping out at 30mph in turbo mode (3rd gear) with both motors going! Here's another question: ever since I bought this late last year I can't get the deck lights to come on. Do you have any suggestions? I'm thinking there's a fuse or wire somewhere that controls the deck lights? Any help you can offer is so appreciated. Thank you!

  • @victorcharleu
    @victorcharleu Месяц назад

    WHAT IS GEAR ?

  • @arminkarajkovic-ct8cj
    @arminkarajkovic-ct8cj 3 месяца назад

    Does this work on any ms energy scooter?

  • @NedSuarez
    @NedSuarez 4 месяца назад

    Hello, can I do it on my nanrobotd6??

  • @punithaselvanrajan9493
    @punithaselvanrajan9493 4 месяца назад

    Plz advice

  • @williewashington2442
    @williewashington2442 6 месяцев назад

    What does error 08 mean? My scooter is displaying that and won’t move.

    • @e-scoottech4051
      @e-scoottech4051 6 месяцев назад

      Turnstile fault

    • @williewashington2442
      @williewashington2442 6 месяцев назад

      @@e-scoottech4051 meaning what exactly? What should I do?

    • @e-scoottech4051
      @e-scoottech4051 6 месяцев назад

      Check the throttle magnet and Hal sensor, sometimes the magnet gets loose

    • @williewashington2442
      @williewashington2442 6 месяцев назад

      @@e-scoottech4051 where can I find the hol sensor?

  • @lukecorso9851
    @lukecorso9851 7 месяцев назад

    Thankyou 🙏 my TF-100 has no p08 setting it just goes straight to p09 is there a way to unlock it? Thankyou in advance

    • @anthonysalamone2017
      @anthonysalamone2017 5 месяцев назад

      Where you able to find any info by chance!? I have the same controller

    • @e-scoottech4051
      @e-scoottech4051 4 месяца назад

      As an alternative solution, if you can't find the option on the display, you can unlock the speed of an electric scooter by checking two wires connected together, which are usually white or grey. Look for the looped wire on the controller that limits the speed. These wires are typically white or grey and are connected to each other

  • @AreX_GoD
    @AreX_GoD 8 месяцев назад

    am I supposed to keep pressing the power button?

  • @HOWHOW3310
    @HOWHOW3310 Год назад

    As long as it is a scooter with this kind of monitor, can it release the speed limit?

  • @adrianhoxha
    @adrianhoxha Год назад

    does this work on joyor g7

  • @jakovmaric1012
    @jakovmaric1012 Год назад

    Thats a lie i have hero s8 in mode 3 it goes 52kmh empty with me on it goes 45max

  • @mattemann
    @mattemann Год назад

    works in zero 10x?

    • @e-scoottech4051
      @e-scoottech4051 Год назад

      No, zero has some loop wires to cut or unplug from the controller

  • @rigogioh9762
    @rigogioh9762 2 года назад

    So good 👍!!!!! Thank you♡♡

  • @ratchfordgeorge
    @ratchfordgeorge 2 года назад

    Next time speak so we can understand what you are doing

  • @mr.nice-boy4867
    @mr.nice-boy4867 2 года назад

    is. not woring i tru same like you but isn’t working why ? help

  • @rxonmymind8362
    @rxonmymind8362 2 года назад

    What's the speed now after unlocking?

  • @MrPlasma01
    @MrPlasma01 2 года назад

    AH, just another amputee , one handed scooter wanker.'

  • @chrisfarrell997
    @chrisfarrell997 2 года назад

    Sorry I have been having electrical drama it cuts out sometime and I still have not, got it to go 70mph I did everything you hope for a reply peacd

  • @chrisfarrell997
    @chrisfarrell997 2 года назад

    It's still only will do fifty three so I do not know what I did wrong please let me know what I can do peace

    • @e-scoottech4051
      @e-scoottech4051 2 года назад

      Did you check the red button next to the key ignition, Eco/Turbo?

  • @Paul1027
    @Paul1027 2 года назад

    will not affect the motor when the speed is changed ?

    • @e-scoottech4051
      @e-scoottech4051 2 года назад

      Not at all, the motor can take the speed without problems

  • @nomadmadox8841
    @nomadmadox8841 2 года назад

    Disable "eco turbo mode" is possible? Im sorry, im from Spain my english is terrible. 😅 Help me

    • @e-scoottech4051
      @e-scoottech4051 2 года назад

      Sí se puede, supongo que quieres turbo siempre activo, si no me equivoco para eso habrá que desconectar la conexión con los cables azul y amarillo conectados a la controladora en el conector macho con los cables negro y gris, espero te sirva

    • @nomadmadox8841
      @nomadmadox8841 2 года назад

      @@e-scoottech4051 queria desactivar siempre ese modo. Pero gracias de todos modos. 👍

    • @merino6260
      @merino6260 2 года назад

      Hola Nomad, yo soy de España también, podríamos hablar por correo para compartir info, tengo un nf plus desde hace 3 años

  • @asherramaly2083
    @asherramaly2083 2 года назад

    If I replace the controller on the Apollo Ghost with this, will this hack work?

  • @alanos.luminous
    @alanos.luminous 3 года назад

    First you need to.cut the White kabel ?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Normally yes, the first models received in Europe did not come with the white cable connected, and only with the limited speed on the dash, but now the recent models you neet to find the withe wire on the controller and un plug it

  • @alanos.luminous
    @alanos.luminous 3 года назад

    I dont get the error if i out the

  • @cricri7769
    @cricri7769 3 года назад

    hero s8 46V no good please ( fr que dois- je faire ?) merci

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Il faut débrancher le câble blanc du contrôleur

    • @cricri7769
      @cricri7769 3 года назад

      @@e-scoottech4051 merci alors le fils rouge sur le bleu et le bleu sur le rouge et bien sur le blanc c'est pour faire jolie !!!!!! mille merci

    • @sqliiif
      @sqliiif 2 года назад

      @@cricri7769 salut, peut tu me dire comment tu as fait stp ? le controlleur se trouve ou ?

    • @sqliiif
      @sqliiif 2 года назад

      @@e-scoottech4051 Hello, i have the same probleme, where is the controller ? i'm french too ou est le controlleur svp

    • @cricri7769
      @cricri7769 2 года назад

      @@sqliiif il paraît qu'il se trouve devant la batterie devant le cache c'est ce que ma dit un pro de trotinette

  • @SagivLuzonOfficial
    @SagivLuzonOfficial 3 года назад

    Please what is the code in Zero 8 ?? Thanks for the help🙏

  • @stevenbokalo8549
    @stevenbokalo8549 3 года назад

    Bonjour. J'ai une héro s8 v2 21ah. Et je n'arrive pas du tous a la débrider. Pourtant je suis bien les informations. Merci de m'aider. :) :) :)

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Possiblement elle est bridé a niveau du contrôleur, il faut débrancher 2 câbles blancs branchés entre eux directement

  • @chrisfarrell997
    @chrisfarrell997 3 года назад

    It just goes fifty three not seventy like I was your one do can you tell me what I did wrong kind regards

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Did you check the red button next to the key ignition on = eco off= turbo

  • @mateojones1129
    @mateojones1129 3 года назад

    Thank u 🙏 🙌

  • @rjshhooba9857
    @rjshhooba9857 3 года назад

    A good advice ,to put the speed limit back, do the same but hold it for 10 seconds, the speed will go back to 25,

  • @chrisfarrell997
    @chrisfarrell997 3 года назад

    I tried what you did it still has not got any faster as I disconnected the wire shown on you video

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      How fast your are going?

    • @angelino1383
      @angelino1383 2 года назад

      @@e-scoottech4051 I did the same I am only going to 48km/hour, do you have any idea why? Its near new, 300km

  • @lauriev7388
    @lauriev7388 3 года назад

    That's works on hero 10

  • @mrhow2712
    @mrhow2712 3 года назад

    My chorus NF scooter is not marking the correct speed. It says I'm going 55mph when I'm only going 25. Would you happen to know how to fix this?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Check your settings, especially in P0(=10) and P2(=15)

    • @mrhow2712
      @mrhow2712 3 года назад

      @@e-scoottech4051 I was tampering with the settings at one point and I may have changed one of those settings. Do you know what the proper number for those settings is supposed to be?

    • @mrhow2712
      @mrhow2712 3 года назад

      @@e-scoottech4051 Oh and thank you so much for the reply

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      P0 = 10 P2 = 15

    • @mrhow2712
      @mrhow2712 3 года назад

      @@e-scoottech4051 awesome thanks man

  • @maryannhansen8773
    @maryannhansen8773 3 года назад

    Hi at the start I get no numbers going backward just stays at 00 what am I doing wrong please.

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Maybe you got a faulty controller

    • @maryannhansen8773
      @maryannhansen8773 3 года назад

      Thanks for your reply worked out that I had to change from kick start and put the rear tyre up. Did it this afternoon and all works perfect.

  • @mfrutos
    @mfrutos 3 года назад

    I have tried doing in mine....it´s a LIVIAE lcd panel, it changed the number of magnets, on P07 so the speed marker make it looks faster, but actually the real speed is the same...it was in my case!

  • @jadenr.4531
    @jadenr.4531 3 года назад

    Can i do this on my joyor f7 electric scooter?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      No idea

    • @jadenr.4531
      @jadenr.4531 3 года назад

      @@e-scoottech4051 im assuming that maybe its possible due to a similar throttle

    • @jadenr.4531
      @jadenr.4531 3 года назад

      @@e-scoottech4051 so can u see if i am able to get my joyor f7 up to that speed or around there, i really want to know if im able to do it

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Normally you can find how to unlock it on your user guide if not I'll recommend to contact your supplier, unfortunately I don't know the model and I can't help you with that but good luck

  • @djcranium1210
    @djcranium1210 3 года назад

    I got a evercross /h5 hitway scooter coming do you reckon it will have a limiter inside like this ? It's a 800w and goes 28mph and I'm wondering if it should be going faster say 38mph without a limiter if it has one .

  • @jeremydelobelle5950
    @jeremydelobelle5950 3 года назад

    Currus fn 10 ?

  • @krystian7858
    @krystian7858 3 года назад

    Works this on the zero 9 step?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      I don't think so, on the zero I believe you most cut the loop and it's a white wire

  • @jeanclaudeloiseau8788
    @jeanclaudeloiseau8788 3 года назад

    J'ai un problème de défaut d afficheur que dois-je faire merci de vos réponses

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      quel est le problème sur votre trottinette exactement ?

  • @adamneon
    @adamneon 3 года назад

    If you want to lock it again can you follow the same process? I'm thinking you might unlock it when you go offroad, then you want to lock it again when you are back on the roads again?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Yes, it's the same

    • @ProfLiebertNogueira
      @ProfLiebertNogueira 3 года назад

      @@e-scoottech4051 Hi. Can we change the lock speed? For example, mine is locked at 20 km/h, but I wanted to go up to 25 km/h. Thx

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Probably your's it's limited by the P08 I'll recommended to check it and if you want to go to 25 just setting up to 25 if not that's mean that your controller it's fiscally limited and you must unplug the wire loop, on the Hero's controllers normally it's a withe wire connected between each other

    • @rjshhooba9857
      @rjshhooba9857 3 года назад

      DO THE SAME THING BUT WAIT 10 SCONDS

  • @rogelioesquibeljr2721
    @rogelioesquibeljr2721 3 года назад

    boss pano mag set up tulad ng ginawa mo kc ung scooter q mabagal boss tulong nmn boss

  • @FaridProject
    @FaridProject 3 года назад

    Hi! do you have to unlock the speed limit anytime you power on the scooter?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      No, once you unlock it, it stays like that

    • @FaridProject
      @FaridProject 3 года назад

      @@e-scoottech4051 Thanks for the answer!!

    • @paolomartirani1101
      @paolomartirani1101 3 года назад

      @@e-scoottech4051 hi and can you revert back to speed limit after you unlock it ?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      Yes, it's the exact same process

    • @thechipnigga8124
      @thechipnigga8124 3 года назад

      Does this work zero 9??

  • @matthewmcgrath1741
    @matthewmcgrath1741 3 года назад

    how many seconds it requires to hold it for

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      10 to 15 seconds

    • @matthewmcgrath1741
      @matthewmcgrath1741 3 года назад

      @@e-scoottech4051 can't wait until it get to my house it said it should be a few more days until it arrives

    • @matthewmcgrath1741
      @matthewmcgrath1741 3 года назад

      @@e-scoottech4051 any tips. I don't wanna break anything

  • @matthewmcgrath1741
    @matthewmcgrath1741 3 года назад

    i just bought the heros8 today

  • @chriswhittle3381
    @chriswhittle3381 3 года назад

    Thanks for answering I appreciate it! 👍

  • @chriswhittle3381
    @chriswhittle3381 3 года назад

    Is this possible on the currus panther do you know at all?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      ruclips.net/video/_0Wb-qpa64s/видео.html

    • @chriswhittle3381
      @chriswhittle3381 3 года назад

      Thank you! Do you know the potential top speed with it?

    • @e-scoottech4051
      @e-scoottech4051 3 года назад

      80 km/h but it depends a little on the weight to be carried by the scooter and the level of battery charge. The more charge you have, the easier to reach the 80 km/h and it would hold for a bit longer

  • @Justme99709
    @Justme99709 4 года назад

    Mate I have Hitway electric scooter 800w type.. I can get 43 45 kph but have you any hints plz so I can make it faster

    • @djcranium1210
      @djcranium1210 3 года назад

      Have you found anything yet ? I was thinking it must have a limiter wire inside

  • @Rainchaser007
    @Rainchaser007 4 года назад

    Thanks for this!! I just got my S8 and could not figure out how to get it past 13 mph, lol. 😆 Was going bonkers.

    • @e-scoottech4051
      @e-scoottech4051 4 года назад

      I'm glad that was useful to you, little advice be gentle with the stem clamp if you tight to much it will break