Видео

About what length did you use on the 2 inch and 1 1/2 tubing on the main frame?

Good looking press , very well done!!

what is the maserments of the tooubes in

Amazing, what size and gauge of steel did you use for the platform?

How did you connect the wheel to the thread? Is that a coupler that you welded to the wheel or how can I do this?

Dude no way Mondragon is your last name? Are you in any way related to Dr. Mondragon who is a chiropractor and has her own RUclips channel??? I’ve never heard of that name in my life until her….I’d imagine it’s a extremely rare name.

Good game. Terrible back ground noise! Ahh music😳

Looking great cowboys!! Thanks for the video 👍

No Thrust bearings? Mine has two eyelets too, but with a .1/2 shoulder bolt. I drilled a hole in the front of my fingers opposite of the thumb screw and installed a spring so when I adjust mine, the finger just moves back and forth without any slop. The springs keep the adjustment screw against the press at all times. I don't know why people leave this feature out. It is one of the easiest parts of the build.

Thanks Kelly!!! Kal-El Fields #59 <3

Thank you for sharing your build, looks great. I built most of this over the weekend, ran into a couple bumps but still very happy with the results so far. Your eyelids that you welded for the fingers( I ordered the same ones off eBay) do you feel that the 1/2 inch hole is necessary or could you of just stayed with the 7/16 predrillled hole? One other question, could you share the dimensions of the eyelids that you welded?

Becker Points

Thank you for taking the time to make and share this video! Looking at your design, I think if I were to follow your inspiration, I would try to make use of both sides of the stand with the press on the far side and the draw board on the near side so there isn't a need to be swapping fingers.

use a ratchet strap or cam buckle strap. loop the ends around you limbs and tighten the strap till your limbs retract. As long as you are careful about loosening them it all works as well as anything you can build .

How did you came up with the video?

you could have the bar for the draw board collapse in to the arm would make it a lil less in the way working with the bow press configuration i like it though well done

Great Highlights Need to get the video taken from the top box! Missing out on a lot of topographical shots

I loved the highlights. They were amazing. Thanks for sharing. Your amazing 🙏♥️

Great highlights, I would love to keep seeing more GHS highlight videos like this! Keep up the good work!

Awesome video. How far did you space your bow finger eyelets?

Impressive. Nice build. 👍

Nice Job!

Do you have a issue with the bow coming out the bottom of press when pressing due to end of the limbs being curled back in some?

Will the airbags respond quickly enough on valves with 1/4” tubing? My friend suggested that, so I bought solenoids with 1/4” ports but now I’m worrying if those would deflate fast enough.

One quick question! Did you use a bearing at the end of the 2 inch tubing, mounted on the all thread. This bearing will support the all thread and turn smoothly. Great build! I like your design where you have the two plates welded to the square tubing. thank you for sharing your design.

FYI...I decided I don't like the angle of the bow when I hang the bow on the bar stock for the draw board. I was worried the string might derail. So I've just started taking the pin out and hanging the bow on the square tubing. It works better because it keeps the bow perfectly square. I may even cut off the bar stock since I won't be using it for the draw board anymore.

Nice build man

Great job, it’s totally insane 👍

Amazing!!!

Could you show the double nut ,on handle!!? Mine is sliding way out before it connects for pressing etc!!

You have a Bill Of Materials and cut list

Be very careful with this. Last Chance has been known for coming after people doing this, especially when your design is pretty much their design.

Looks good man!!! 👌

Nicely done! 👏👏👏 I’d like to start working on my own bow but bow press and draw board are $$$$. Too bad I don’t have the equipment/tools to build this.

Nice Job! I have been contemplating doing this instead of spending the $1000 on one. Thanks for the links.

How long is the tubing for the press

You built this for 150$-200$?

Hey there! Amazing set up! How did u make the laser swamp?

What on earth

Sometimes I search "student video" or "school project" and sort by new just to feel the devestating second hand theater kid energy but you all absolutely 100% committed to your roles I would like to formally endorse Tanner Perkins as class president of Placeville, Stateland 👏😔

Wow!!! Phenomenal!!’n 😱😍👍

Another question. How do you control the amount of incoming air for each bag?

Hello and thank you very much for sharing. What are the dimensions of your elevator's basket?

That is amazing!! Well done!

Hey awesome job! I am making an elevator this year , just curious where you got the video on the tvs and of it is possible to send it to me ?

Hello. Thanks very much for sharing your project. I commend you for that. Where did you get the air springs from (make model);also, what type of solenoid valves did you use? Finally, how big is the compressor on your amazing video. Thanks

Very nice.

Since this is an industrial elevator, We ask that you use caution when riding. You might find it interesting to know that this exact elevator shaft has been in place for almost a century discovered long before Kennywood was ever built. Sealed shut for nearly 50 years. No one has actually gone down under the shaft.....

Gg

We will be back😉