- Видео 253
- Просмотров 569 820
Auto tech
Добавлен 8 сен 2022
ENGINE/TRANSMISSION mechanic repair
Видео
Car won’t start, making just clicking sound
Просмотров 647 месяцев назад
Easy way to fix your car when sometimes makes only click sound.
Ford - Mazda 3.7 - 3.5 engine ECM / PCM location
Просмотров 618 месяцев назад
ECM -PCM location for Mazda Ana ford 3.7 engine
Ford / Mazda .3.5 -3.7 L engine timing chain set.
Просмотров 949 месяцев назад
Ford / Mazda 3.5 /3.7 L timing chain marks set
Dodge charger/ challenger/Chrysler .fuel pump replacement
Просмотров 1009 месяцев назад
Fuel pump replacement
Land Rover - Jaguars 2.0 L engine timing chain installation/ diagram
Просмотров 18310 месяцев назад
The way to set timing chain for jaguar and Land Rover 2.0 L engine.
GMC Yukon / Chevrolet Silverado , A/C blows one side cold another side hot .
Просмотров 13411 месяцев назад
A/C fix blowing hot side and cold another side.
Land Rover - jaguars 2.0 L engine crankshaft position sensor location
Просмотров 31711 месяцев назад
Crank position sensor location.
Land Rover- Jaguars 2.0 L engine serpentine rotation.
Просмотров 16811 месяцев назад
Diagram for serpentine belt
Chevrolet - Buick traverse. Code solved code P. 2128 - code p 2138
Просмотров 18211 месяцев назад
Bad throttle pedal position sensor.
Chrysler / Dodge. 3.6 L engine, runs roughly shown bank 1 and bank 2 system too rich
Просмотров 27011 месяцев назад
Was intake valve stay open making all trouble codes
Jaguars 2.0 L Engine Engine removal
Просмотров 265Год назад
The way to pull engine out for jaguars 2.0
Jeep -Dodge - Chrysler. 3.6 L engine timing set
Просмотров 268Год назад
Jeep - dodge timing set up.for 3.6 L Engine.
Nissan , Rail fuel pressure sensor replacement.
Просмотров 16 тыс.Год назад
Easy way to replace rail fuel pressure sensor
Hyundai /Kia Air bag module replacement
Просмотров 8 тыс.Год назад
Hyundai /Kia Air bag module replacement
Honda A/C evaporator / and heater core replacement
Просмотров 220Год назад
Honda A/C evaporator / and heater core replacement
Honda - pilot - accord evaporator and the heater core replacement
Просмотров 4,3 тыс.Год назад
Honda - pilot - accord evaporator and the heater core replacement
Kia / Hyundai Steering Clock Spring angle replacement.
Просмотров 264Год назад
Kia / Hyundai Steering Clock Spring angle replacement.
Kia / Hyundai airbag module location
Просмотров 1,1 тыс.Год назад
Kia / Hyundai airbag module location
Dodge-Chrysler-Jeep 3.6 L engine camshaft replacement ,easy way
Просмотров 1,1 тыс.Год назад
Dodge-Chrysler-Jeep 3.6 L engine camshaft replacement ,easy way
Chrysler- Jeep- Dodge . 3.6 L engine timing chain installation.
Просмотров 455Год назад
Chrysler- Jeep- Dodge . 3.6 L engine timing chain installation.
Hyundai / Kia steering wheel , making clicking noise . Fixed easy way.
Просмотров 301Год назад
Hyundai / Kia steering wheel , making clicking noise . Fixed easy way.
Dodge / Chrysler , how to add power steering fluid.
Просмотров 238Год назад
Dodge / Chrysler , how to add power steering fluid.
Toyota RAV 4 transmission, this is how to add transmission fluid.
Просмотров 1,7 тыс.Год назад
Toyota RAV 4 transmission, this is how to add transmission fluid.
Chevy 2.4 L engine timing chain installation
Просмотров 310Год назад
Chevy 2.4 L engine timing chain installation
Nissan 2.0 L engine timing chain installation
Просмотров 2,1 тыс.Год назад
Nissan 2.0 L engine timing chain installation
Toyota - Tundra - Sequoia - Land Cruiser,5.7L engine- 4.6L engine , how to set the timing chain.
Просмотров 1,3 тыс.Год назад
Toyota - Tundra - Sequoia - Land Cruiser,5.7L engine- 4.6L engine , how to set the timing chain.
On these engines, can the timing chain n guides be replaced without removing engine? I know Audi timing belts can be done with the engine in.
No you don’t have to remove engine
What tools were needed
Little 5 mm socket , instead of opening you should go clock wise as you tighten
Hi everyone, my actuator was broken for about two years, I just kept procrastinating before I tried to fix it. My coolant sensor went bad and I HAD to fix that. Disconnected the battery, did the sensor change and it took me about two days to realize my power door lock actuator started working again! Just may want to try it before you rip the door apart. Good luck! Please give me some feedback.
You forget mentioning to disconnect the battery, very important step
Yp thanks
How did you access the top bell housing bolts like that? Everyone says you have to drop the cradle to do this job
You be able to get to them
if theres oil in front of turbine when you remove the black tube where air flows is that mean its done??
If too much oil , if just little no problem
Hello i took my kia optima 2014 sx to a workshop and they want to change whole steering column, do you think i should take my care elsewhere?
No you should change it without taking whole thing
It’s not hard
Weird looking F150
That’s what is
This is the clock spring not the steering angle sensor
Thanks
👀🤛🏾😎 Handled like a Boss!! Thank you.🏁🏁🏁🏁
Thanks
I have same code on my 2015 Buick lacrosse i replaced the Fcpm and air shutter valve code still coming on any ideas
Could be module it’s vlose to fuel tank
Thx for explaining
Thanks
you just change the chain and tensioner and solve the code P0017?? I had a elantra 2017 with the same problem and i think thats the fault in the engine, because I inspected the variable gears and I see that they are fine, but the tensioner does not move smoothly. before at all this i replace the exhaust solenoid as it was stuckt, but the signals and voltages are fine. Can you explain me the problem in your case?.
Hi check the pin the one goos between camshaft and gear the key sometimes breaks.
@@autotech9043 I check that pin, and it's fine.
This is not the same flr the honda pilot
Yes its Honda pilot
@@autotech9043 then probably different generation. I'm dealing with a generation 1 Honda pilot. The process is more difficult to say the least
I have a 08 Silverado and changed the fuel pump twice and still showing that p069e code and also wants to die on its own. I domt wanna buy the control module if it isn’t the problem
I think that’s a problem
Do u think it’s the control module
Excellent, Is this for qr25 engine?
All 2.0 are same
Eso que le hecha a las bancada del ciguañal es aceite? Que número es recomendable usar gracias
Sorry , no espaniola
It is engine build lube (assembly grease)
What year is this scion trying to find timing marks for 2007 scion tc but can't find any your the closest I've been able to find
Hi , that’s same Toyota is it 1.8 ?
It's a 2.4l
Sometimes when I'm driving and hit the brake pedal the steering power goes off, do you know what it could be causing this? When I use a scanner tool the codes are 1260 and 2412, if i delete the codes i get power steering for a while and then it fails again
Change spring clock , the same the one in the video, good luck bro.
@@autotech9043 Thank you, I already bought it and should arrive tomorrow.
My issue with my 2017 GMC Acadia limited is that it drives fine when it’s cold and a bit warm but once really hot stars to shudder really bad on take off and on reverse would changing the tcm help solve my issue?
No I don’t think so Tom, could be transmission filter dirty, try to flash the the transmission fluid , it may help. Thanks
Thank you for this video. I’ve done Hondas before about to go tackle one of these this morning. Seems very similar
Thanks got ur comment
Thank you
Wow... Literally you did this job single handed and not a torque wrench nor sealant in sight. Amazing..
Thanks bro
What car is this for?
Kia / Hyundai
Excelente
Thanks bro
Stuck on getting the camshaft pulley out Any tips?
mine had bad exhaust phaser took off valve cover, tired moving exhaust Cam, sure enough it rotated freely out of sync with timing assembly. if you go this route don't use a lot of force to move cam bc your turning engine with basically the cam shaft. just enough force to see if free spins and if free spins do not start car afterwards the valves may be damaged. codes p0017, drove like this for a while. i got lucky. about $2000 repair at shop
The most time the key broke the one hold the phaser to camshaft.
probably a 2015 for anyone wondering since its not in title or desc
The most are the same
Thank you!!!!!! Tearing back into one I had kid work on for me..... rear head is 180 out..... foook needed verification before busting balls.... hope valves and pistons are OK.
Thanks
Thanks for your help
Thanks to you too
How long did this job take?
It does takes 6
Takes 6 hours
No explanation or anything. DUMB ASS VIDEO!!!!!
Thank you, so simple got it on the first try.
That’s good, thanks
Thanks for making a video that ACTUALLY shows the real work needed to get it done. Music is annoying though.
Sorry for that music , thanks anyway.
how I HATE videos with loud clear noisey music.....yet when the person speaks.....YOU can Never hear them talk
Sorry for that.
Thanks
Whoever designed this should be horse whipped! Having to disassemble and reassemble all of this just to replace a sensor?!!! It's insane! They couldn't have just put it in a location easy to get to? It's just a money making scheme... most of us would have to carry it to the dealership or Kia mechanic and it probably cost a small fortune to get it done!
I know it’s a lot of cars same problem,it’s good for mechanic to make more money
Today the dealer told me it it would cost $695. for a 2019 Sorento. The oil light has intermittently went on for the last 18 months. Not sure it needs to replaced if it's not leaking?
Had this motor in a sorento for 80,000 miles at which point the car was sold. Never a problem with it and it was super powerful in that car.
Yes they have the same engine, Kia and Hyundai are same
what was the problem ?
Sorry for delayed, had an emergency. The proteas the pin holding the gear faser to the camshaft broke.
Question: My intake cam is set flat for the cam locking tool, but I have to twist my exhaust cam a little bit clockwise to fit the tool in the rear slot. This opens up the exhaust valves slightly on cylinder #2, is this normal?? I have my old head and a rebuilt head, it’s the same. Also, since we took the cam phasers off, how do we set them? I can’t see any marks showing which position they should be in. Mine have numbers 1 and 2 showing on the face, I think 1 is for the intake side…?
Also, thanks for the great video!
Hi, sorry for delay, you need just put the tool in faser and tool from the back of camshaft, and also another tool goes to the crankshaft.
This has two different alignment marks in every sprocket, I will put it like the position that you used and I will try it, tanks for share it!
Yes same the one I put
Sorry for delayed
Thank you for your expertise
Thanks
What grade bearings?
You should measure the crankshaft see what you need, standard or oversized
Did you replace or clean it out ?
Replaced it
@@autotech9043 how did you know it was the vacuum pump and not the brake booster or master cylinder?
Sorry my 2016 200 brake is spongy just happened yesterday, was driving and when to brake and it was like knocking or kicking back, when I had to apply ton of pressure to stop, did the start the engine hold brake and turn it off while holding 30 sec and pedal did not rise or fall just stayed, no engine but brake light on.
If the brake pedal hard and not holding
the engine must come out of the car in order to replace the chain?
Not really
You can do it there
Hi i have a p0017 code. Changed both solenoids. Car runs but the code still pops up. No engine knock. But I was told it could be that before they even looked at it what should I tell the mechanic to inspect ?
On hot and or cold there is no engine knock.
It’s a 2020 Hyundai Elantra 2.0l engine
Check the camshaft gear the pin lock if still in place
Do you have another video to explain what part needs to be taking out? I have 2014 Chrysler 300C 3.6 pentastar engine
Yes I did a lot of them , just look more you will find out .
@@autotech9043I’ve watched a couple of videos you posted about the same Engine Size. After I changed all rockers and lifters, I noticed the knocking Noise sounds when the RpM goes up above 3, do you think it’s a Rod Bearing for sure? I also I keep getting code P0019 crankshaft Position-camshaft position correlation Bank 2-Sensor2. Do you think it’s because the spark plug I just changed and got them from Amazon? Thank you for your help 🙏🏽🙏🏽
Might as well just took the whole subframe out your way 🤷🏻♂️
Yes that’s better .
hey man, i have a 2018 elantra 2.0L 141.000 miles I have code p0017 and p0014 i stall sometimes at low speed/stop signs/red lights have some trouble start the engine sometimes and it makes a weird noise, it’s also shaking it has trouble up shift gears (takes a long time to up shift), so poor acceleration and rpm jumps because it takes more time to upshift do you have any ideas? thanks! 🙏
Hi , the first check transmission fluid, did you scan it ? What is the code ?
@@autotech9043 Scanned what? I scanned the car and p0017 and p0014 I thought transmission fluid should never be replaced on this model?
What was your issue
@@naweedshalizi8496 the issues was the faser of cam shaft pin broken the one hold gear to camshaft
Is the new airbag module require programming?
Don’t have to
No ,? Don’t have to.