Sir i need your help. I am going to develop one application using this controller . The application is "when limit switch is ON motor should run in one direction for given steps .
Hello.. What do you need to know about controller.. Is possible do that, just yo need to get pulse on/off 5v or 0v that signal you can test in outsides CW dir and CWW pul.. For turn on/off the limit switch and make stop or advance..
hi sir i want to use the controller for building coil auto winding machine ,can the controller drive the coil slider clockwise and stops at the programmed count and returns back to start up . this process will continue arranging the coil until the counting stops
hello manuel i was wondering if this device can be driven off a encoder , wat i need is sumting that can translate the pulses from an encoder on an electric motor to a movement on a steppermotor , problem is i need a ratio (like one step per x amound pulses from the encoder)i need it for a cilinder hone machine but its about the same setup as an electronic lead screw for cutting treads single point if this device cannot do it are there other (cheap) devices available that can ?
Hola Menuel ocupo controlar Servo Stepper Motor para un Actuator Linear en forma vertical, para un proyecto de homeopatia, lo que llamamos POtentizar el medicamento, puedo enviarte un email y a donde por favor ?..muchas gracias
Hello sir. Do you have a phone number or an email to contact you about this controller. I am a student and I am doing an experiment and I really need your help because I’m struggling with this controller
Hi Manuel ,i am wondering if i can use that controller for a NEMA 34 stepper motor and if so, can I add an external Button to activate the selected mode?
Yes, you can wiring a external, buttons and sensors for star the controller, it's so simple add external components for turn on- off, send a digital pulse and receive digital signals.
@@albertopaz1223 no problem, dou you remember that the power driver external will move the Nema 34, the controller doesn't have power inside, just send digital pulses to control the automation only.
buenas tardes sr manuel gonzalez, por el nombre es latino , asi que comprende el español, ese programador , da para hacer un programa que , insiera el valor y el movimiento transmitido sea en mm, para automatizar una guillotina de grafica , inserimos el valor en mm y ese equipamiento transformaria el valor en pulsos que genere la cantidad correspondiente a mm en un fuso esferico, como en un programador cnc????
What is conection wite , driver and motor ?
Здравствуйте 🤝. Как Я могу настроить его ? У меня не получаеться …
Please show 5 phase motor connection
Sir i need your help. I am going to develop one application using this controller . The application is "when limit switch is ON motor should run in one direction for given steps .
Hello.. What do you need to know about controller.. Is possible do that, just yo need to get pulse on/off 5v or 0v that signal you can test in outsides CW dir and CWW pul.. For turn on/off the limit switch and make stop or advance..
Bom dia você tem essa demostração em espanhol?
Si la haré en español, con el controlador igual
hi sir i want to use the controller for building coil auto winding machine ,can the controller drive the coil slider clockwise and stops at the programmed count and returns back to start up . this process will continue arranging the coil until the counting stops
Tienes que engrasar un poco dañaras empaques
Que tal Amigo, El tanque tiene poco aceité, menos de la mitad será por eso que brinca el pistón, ya ves como sube?
@@ManuelGonzalez-pj1bj el cilindro se ve corroido el tiene que estar liso para que desplace suave saludos desde Colombia
El esquema de como se conecta lo puede facilitar???
Se conecta solo Pulsó (-) Dirección (-) Optó acople 5v Y Encendido 24v + vdc Y Negativo - vdc
Hola usted podria enfocar el coneccionsdo del controlador con el drivers orfavor
Hi, could you please provide the wiring diagram?
hello manuel i was wondering if this device can be driven off a encoder , wat i need is sumting that can translate the pulses from an encoder on an electric motor to a movement on a steppermotor , problem is i need a ratio (like one step per x amound pulses from the encoder)i need it for a cilinder hone machine but its about the same setup as an electronic lead screw for cutting treads single point if this device cannot do it are there other (cheap) devices available that can ?
Hola Menuel ocupo controlar Servo Stepper Motor para un Actuator Linear en forma vertical, para un proyecto de homeopatia, lo que llamamos POtentizar el medicamento, puedo enviarte un email y a donde por favor ?..muchas gracias
Can u show the wiring?
Hello sir. Do you have a phone number or an email to contact you about this controller. I am a student and I am doing an experiment and I really need your help because I’m struggling with this controller
Hello WhatsApp +523334435302
Good morning mate. I'm having trouble setting up this driver. Can you give me a support?
Good morning mate. I am wanting to buy this driver, can you guide me about it? Is it of good quality? Thank you.
Hi Manuel ,i am wondering if i can use that controller for a NEMA 34 stepper motor and if so, can I add an external Button to activate the selected mode?
Yes, you can wiring a external, buttons and sensors for star the controller, it's so simple add external components for turn on- off, send a digital pulse and receive digital signals.
How about NEMA 34 stepper motor? Its a kind of large motor ,can this controller handle it? Tnx un advance forma tour time and kindness
@@albertopaz1223 no problem, dou you remember that the power driver external will move the Nema 34, the controller doesn't have power inside, just send digital pulses to control the automation only.
Thank you again Manuel, i will order it, and let you how is it going, is it ok for you if contact you again if have any issue ?
@@ManuelGonzalez-pj1bjIf I want to send out a pulse output to a DAQ to start another program, how should be the wiring of motion controller and DAQ?
Like a $60 dlls, more or less
Price? ,
www.automationtechnologiesinc.com
Nice www.automationtechnologiesinc.com
buenas tardes sr manuel gonzalez, por el nombre es latino , asi que comprende el español, ese programador , da para hacer un programa que , insiera el valor y el movimiento transmitido sea en mm, para automatizar una guillotina de grafica , inserimos el valor en mm y ese equipamiento transformaria el valor en pulsos que genere la cantidad correspondiente a mm en un fuso esferico, como en un programador cnc????
An excellent controller, as soon I can going to put application video, about 1axis movement, in desplacement of machine.
www.automationtechnologiesinc.com/products-page/cnc-controller-box/1-axis-cnc-servo-stepper-motor-motion-programmable-controller/