Видео

Bitte senden Sie mir ein Deutsche Übersetzung das Programm ist super MfG Friedrich Heckel

Hii thank you for the video! I recently bought the same setup with the Servo57D motor. I tried running examples 2 and 3, and while I can see the real-time position and speed readings on the motor's display, they don’t appear on the serial monitor. Could you please help me troubleshoot this issue?

Can this be done in klipper firmware?

Plug and play Robotic arms may make so many machines like this obsolete sooner. And they cost less for industrial setup.

İyi geceler Sizden bir konuda yardım istiyorum Elimde mksdlc 32 v2.1 kontrol kartı ve 5.5 W güce sahip bir lazer var tasarladığım makinenin mekaniğini tamamladım elektronik bağlantıda zorlanıyorum Lazerimden 4 adet kablo çıkıyor başka bir karta giriyor girdiği karttan 4 adet çıkış var 12v + 12 v - Ttl+ Ttl- Mksdlc 32 v2,1 kartta bu kabloları nereye bağlamalıyım? Yardımcı olursanız çok memnun olurum Şimdiden teşekkürler

As a 3D printer manufacturer, I think I will never use an MKS motherboard again. Because I'm about to go crazy. I rewrote the bl toch screen according to Marlin 2.1.2.5 version and also made the mesh bed leveling screen and I thought everything was OK. This time, I cannot connect the motherboard to the computer via USB. I cannot calibrate the pid. When I connect via Wifi, I send the m503 command and I don't get any results. When I start PID calibration over wifi, the screen freezes and I cannot get PID results. Please help me how can I run m503 etc. commands with repetier host or pronterface programs, how can I connect to the motherboard with a cable...

As a 3D printer manufacturer, I think I will never use an MKS motherboard again. Because I'm about to go crazy. I rewrote the bl toch screen according to Marlin 2.1.2.5 version and also made the mesh bed leveling screen and I thought everything was OK. This time, I cannot connect the motherboard to the computer via USB. I cannot calibrate the pid. When I connect via Wifi, I send the m503 command and I don't get any results. When I start PID calibration over wifi, the screen freezes and I cannot get PID results. Please help me how can I run m503 etc. commands with repetier host or pronterface programs, how can I connect to the motherboard with a cable...

Hello everyone, I am using the MKS Robin Nano V3.1 board, but I couldn't establish a connection to the PC via USB cable. I can only connect through Wi-Fi. However, when I send the M503 command through programs like Repetier and Printrun, I can't view or modify the EEPROM settings. Even though the EEPROM_SETTINGS option is enabled, I am unable to see or change the EEPROM settings through the program. Does anyone have any suggestions on how to solve this issue? Any help would be greatly appreciated!

Bom mesmo

Tengo un laser TWOTREES TS2 de 20 W. Controlado por una MKS DLC32 V2.1 , Pero tengo un problema que no tengo salida par poder conectar un Rele o un moss y que me active la salida para poder conectar la asistencia de aire, se puede hacer modificando el Grbl o tengo que comprar otra placa diferente a esta . muchas gracias

When I try to upload a print job via the web interface, I get a no SD card detected error. This is despite having enabled SD card support in Marlin 2 and having a known working SD card formatted as FAT32 inserted. Please advise.

what software need use if use only whit PC windows10. how connect wifi, lot different all display button options i have version 2.1

i just buy same controller version have V2.1 but i not know how connect to wifi and what app need be phone, and what need be to computer. different display i have, not have display confurication button and laser have 0,1mm 1mm 10mm only. move. first time plug power today and lot different all display selection buttons have, i not know what firmware this is. and not know what laser i need buy this, TTL or PMW controller laser and how more Watt need be. need use normal whit PC how ? phone not good controll anythink. i like use PC.

args from python: [] Traceback (most recent call last): File "C:\Users\gamer\AppData\Local\Temp\1m2eIZGTRxmt3FzYSWZkn2xgNP8 esources\server\odrive_server.py", line 293, in <module> shutdown = fibre.Event() AttributeError: module 'fibre' has no attribute 'Event'

Issue with Marlin 2.1.2.5 on MKS Robin Nano V3.1 with MKS TFT35 V2 Screen Hello everyone, I'm experiencing some issues with my 3D printer setup, and I would appreciate your help. Here's my situation: I have successfully uploaded Marlin 2.1.2.5 (the latest version) to my MKS Robin Nano V3.1 board. I’m using an MKS TFT35 V2 touchscreen. However, many features I’ve enabled in Marlin are not displayed on the screen, even though the same firmware works fine with a Reprap graphic display. For example: Mesh Leveling: I’ve activated 25-point matrix bed leveling, but during manual calibration, only 5-point calibration appears on the screen. Input Shaping: I’ve enabled input shaping in Marlin, but the screen doesn’t show the interface to enter frequency values. Soft Endstops: I’ve also activated the soft endstop feature, but it doesn't show up on the screen either. Does anyone know what might be causing these issues or how to fix them? Your guidance would mean a lot to me. Thank you!

can the board be reprogrammed to perform other functions, not just 3D printing? e.g. If want to control motors on a robot or for some movements of scenery on a model railway?

Is it possible to add a Display with throttlr so I can chech Speed, voltage e.t.c ?

hello i am having issue with SPI encoder error 257 , can you help

Can the MKS SGEN-L V1.0 work with the MKS-MINI12864-V3 to use the M500 save function? Or, if I enable it, will it save to the SD card instead?

Hi, do you have any instructions on how to upgrade the firmware for the MKS Servo42D board? I have firmware 1.0.4 and I need 1.0.5 or 1.0.6. I've looked everywhere but no luck so far... can someone from the MKS Team help me out?

This video has a mistake at 3:58. In addition to the confusing order in which the video was edited, at this point it is shown that it should be connected to the Z+ connector when in fact it should be connected to the Z-, since the installation of the Bl touch is based on finding the minimum of the Z axis. I wasted a lot of time with this until I finally resolved it, so this is a warning for others who will try to do the process.

Hello, why does this board not work with the filament sensor?

Hello, I'm having a problem with the configuration within Marlin, in fact, everything is exactly the same as in the video, but on my Ender 3 with Robin E3D board, if the filament sensor is on, when starting printing it changes position, starts to retract the filament, asking to change it then appears on the screen asking to purge, this happens about 3 times, after that the option to continue appears... the printing continues, but when the filament runs out, the printing does not stop and the printer screen says that the printing is paused. What could it be!? Tnks

If you want to copy the commands, this is the blog: blogDOTcsdnDOTnet from gjy_skyblue. It is article number 119669725.

Is this the same setup for multiple motors on the same bus?

7:12 which lines need to be commented out for the Mini V6.7?

Good job! Waiting for 48V version!

why the MKStool cant be use for now in 2024? im so upset

Hi ,It`s excellent board i use it on fiew my machines ,can you back in new firmware automatic WiFi reconnection?

Can you use high Kv motors like for drones using this controller?

why is the TinyBee not there ?? it's your product !

I have a 42D CAN board that is showing firmware version 1.0.4. I need firmware 1.0.5 in order to use sensor-less homing. Is there a way to upgrade the firmware on the board?

Roxane Union

Файно 🔥

hola, coloque la aplicación en ingles pero la mitad de las opciones me aparecen en chino, no puedo agregar la impresora

The one I received had the wires mounted in opposite directions causing my motherboard to fail

Mks Laser Tool Not Available? Mks Tool only Robin Boards, Not dlc32...

Runolfsdottir Causeway

bad gateway 502. Link not working

502 Bad Gateway

How to control and read position of multiple MKS Servo 42C ( three step motor) with Arduino Mega. Please, help me !

Can you please not use computerised voice? It sounds like a 5 year old learning to read.

What does this board do.....?

Can I use REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER?

Please I need video for mks LA esp32 pro

I have 2 boards, MKS Robin E3 and a Robin Nano V2.0, I can't put Klipper on them, please help

Ist kein Fake, habe die Fassung vom Stecker vorsichtig abgezogen und andersrum gesteckt. Jetzt passen auch die Kabels, ohne die Nase abzuschneiden

there is no Auto power fail Resume features...

Is there no way to connect TX/RX for CANBus transceiver? I ordered a few of these because esp32 has plenty of IO, only to find barely any of it is exposed to use. Just the I2C and no SPI or TX/RX?

Thanks for the detailed video, Do we have Tutorial for integrating Arduino with 42D CAN module. I have a project with this requirement would really really appreciate your reply on this.