Видео

What is this first lever on the bottom left? Cause the right one is to operate the dozer, right?

Hi I have a 3284 (28hp I think) it must be 12 plus years old and has given great service - I find Sota Tractors to be very helpful. It doesn't run as smooth and as sweet as my other tractors (a 25hp Kubota and FE35 3 cyl Fergie) but gets the job done just as well and purchase price was much less.

the sound at 13:16 which comes from middle of rotating part, i have that too. Do you have any problem with it? or it is just normal so far?

I bought a Xn12 and it is ok for the price, what makes me sad is that the manual is very bad, I have used it 40 hours in two years and many places are rusty, after 40 hours of use something is wrong with the engine, I took removed the cover of the engine to see what is wrong, and under the cover I found out that the welding work was very very bad, it looks like the welder could not weld, the rolling rubber band has many cracks on it, I don't know how to refilling the hydraulic oil in thanks if I want to do one day, nothing about it in the manual,

We have an Apollo 55 hp. It's 9 years old with 1200 hours, and we have had no issues with it. Very basic but also very reliable

Very useful 😊

One question do you know how many hydraulic pumps are on it besides the 2 drive motors?

Nice review. A little small for me but if it works for you that’s great! Love the sound of diesel motor. It’s far better that a briggs gas motor.

Take your hands out of your pocket for my safety!!

4:50 you call it easily filled? Imagine having it on trailer at gas station and line behind you. And then you start to disassemble piece of machinery to fill that half bucket sized fuel tank for 4$. This is some kind of joke. This tank may be was meant to be for hydraulic oil originally

Its not yamnar its yanmar :P I think the buckets without teeth is called planning bucket. Would have been fun watching you dig a bit with it.

Can uake a long review of it pls

I did extensive market research, and apparently RINO XN machines are the cream of the crop of all Chinese manufacturers. This is probably why you have had a good experience. I chose to go the middle route and went with a small factory adding all the features like the swing boom while not paying top dollar. The main downside is the cheapo Briggs 420cc vs kubota oelr yanmar diesel. I'm also glad that I am by the bargain basement ones where they cut to many corners and I also resellers.

Where did you source the XN12 from ?

Whatever you do don't try to buy clutch plates, the thieves will only sell you a clutch kit pressure plates and all about $2.000.00 So get them re faced or do it yourself!

What is the swl

I've read the manual, I don't like it. the explanation is not good, I can't find any information about the maintenance, I can't find any troubleshooting stuff online, I can't buy any repair book, they keep people completely blind about the excavator,

What size machine is it

Very few people watch tractor videos to listen to music. They would much rather watch and listen to the equipment, not music! Tractor videos were not designed to be music videos.

Why in the world would you track without the engine at full speed? 🙄 No wonder it moves so slow. You should get an excavator with two travel speeds, like a lot of them have.

Just curious what the US equivalents were for the size of your trenches or pits.

Very Well Machine

Nice presentation. Glad you have found great uses for it.

Quanto è costato?

That fuel tank would be so bloody annoying

👍 👍

Glad to see your video .

I'm sure I've seen other Rhinoceri travel faster than yours does. I'd be looking at the hydraulic controls to make sure that you have full movement of the valves and also any other restrictive or speed limiting devices in the hydraulic circuit which may be limiting travel speed in the name of operator safety.

So where did you buy this machine ?

Hello great review on this machine. I'm thinking of buying one too . A person gets a real value for there dollar buying a machine like this . Although name brand machines are nice but way over priced . Well hope to see more of the excavator in action .

How long have you been working with that machine? Is it good?

Well done very nice review. This version with the yanmar does seem to be the one to choose ahead of the single cylinder version. It's all horses for courses and this machine suits you well. Probably still worth $10,000 or more.