Видео

Can it paint your line

I have a 1025R and the box blade that came with it but never has been attached. The whatchamacallits don't seem to physically be able to get wide enough apart to fit over the box blade pins. What is going wrong here?

Well having the tierod behind and below the axial is no better than the kubota and it could be worse because the 3e tierod is the lowest Point on the tractor and the kubota's is not and the hole thing about the petals is just a preference that's all it is and why would everyone want a plastic tractor you can fixe steal you can't with plastic and plastic Well get weaker with age steal won't we have a kubota B3200 and the hud as a good sized dent in it and ges what no rust and it had that dent for at least 12 years and a plastic hud with that much age would probably shater or at least crak if something hevey ish landed on it and haver thing else that is plastic on the john deere which is entire operator stashin also the kubota lifts more and higher

First comment whos who .

Thank you! I needed a quick how to on this. Grateful.

As a cable guy, this is exactly what

Wat ever he just said

Love this channel. Hope harvest treats u well!!

I say this with tears In my eyes, You are the epitome of the American Dream. Your company along with the 3 generations have created an amazing product built from hard work, love and blessings. Well done Ralston Family, your work ethic and love shows in your Amazing Rice. No one can compare to what what you have achieved. Many blessings to your family. You have restored my faith in humanity 🙏

Need to add more hp

I need help learning how to adjust the middle bar. Box is tipped back on angle.

Very helpful

Sou do Brasil, adoro os tratores Joonh deer, e GPS. Tenho MF, Niw Hollande, Joonh Deer.

I❤JohnDeere😊

Promo-SM ✌️

Thumbs up but that was a pretty bad instructional video.

This is one of the most useless instructional videos on RUclips, congratulations!

So how does the unloading rate offset work?

🤳

❤

Thanks for the video. May I share the gospel of Jesus Christ with you ?

You didn't show us anything.

It automatically goes to auto when plugged in

Thanks for nothing

THIS IS TERRIBLE ADVISE / DEMONSTRATION!

Thanks for the speedy demonstration. No extra talking. Good.

Stop computer stop

Ekrandaki traktörün kuyruğunu nasıl kisalta biliriz

what a useless video

Best FEL removal video out there for a JD tractor. The other guys' videos yak and yak and yak yet this video is short, to the point, great video with explanatory graphics, and NO talking! Thanks Greenway.

That automatic kickstand is sweet!

How do you change out and put a new arm on

Wish you show how remove the move when 3 point hitch

should have turned off tractor before unhooking pto shaft

What size twine are you using

Stupid video

Make more videos

That was easy

I have a exact model this was helpful question fluid for the gear box dip stick below lift shield above pto line correct what is the fluid to top off gear box thanks

Thank you Mr. Stan for a good straight forward video. I just bought a 2038r with the same loader and I’m new to all of this. Prior to this tractor I had a 1979 JD 850, so I have a lot to learn. Thanks again.

Awesome. My dealer talked me out of a QH. He has proven to be mediocre with tractor knowledge. I have a Kubota M7060 with a 84" Gearmore hydrolic ripper box with a float tail. So, I also have top and tilt so 6 way on the box 3pt. I'm not seeing how I can use the tilt on the 6 way. Would it bend the left 3pt bar? Can you use them with top and tilt?

Didn’t show how to disengage drive shaft

Yikes

How do I set scv to auto as well?

I wish you would have discussed the sway bars

Yes but hook those pins in the storage holes above.

Will an 1800 display paint where you've been and also will it count acres?

S760. Monitor says no viewable feeds. Any idea how to get the backup camera on?

Good

Good video... I made the mistake of putting the twine in the wrong arm... Now I can retread it the correct way...