Видео

In this video I work on a project that has been put aside for a couple of years. It is an offset smoker built from an old air compressor tank. I cut some strips of 20ga sheet metal to use for the seal and I weld on a handle. I use a tig welder because I can't stick weld thin material.

In this video I remove a broken bolt by drilling a hole in the bolt and then using a bolt extractor. Then I talk about my next project, which is build a turbo kit for an LT-1 engine, the gen2 small block.

In this video I hook my everlast 160 sth up to my predator 8750 generator to see if I can weld with it. My everlast tig/stick welder is an inverter machine and requires clean power. My harbor freight predator 8750 inverter generator is supposed to be clean power. The generator and welder are matched up as far as power output and input are concerned.

I changed the oil on my predator 8750 generator. This predator 8750 is the most affordable inverter generator of its size. I bought it at harbor freight for about 1400 dollars. I accidentally ran the generator twice the recommended time between oil changes, but it seems fine. The power was off for about 4 days, because of Hurricane beryl. This generator ran for about 15 hours a day during the p...

In this video I take the gas tank out of my truck. This is a 1972 Chevrolet C10, so the fuel tank is behind the seat. I'm not going to fully restore my truck, but I do have a hole in the floor to weld up, and I wanted to check the condition of the fuel lines. Also fix the fuel gauge.

In this video I get my 82 Chevrolet truck c10 running again after 8 years. The engine is a 305 chevy with a 2 barrel and HEI distributor. The engine is not the factory engine but should be similar. I go over sort of a checklist of things to get an old carbureted small block chevy running.

In this video I install a gas lens kit and a furick 12 ceramic cup. I then tig weld some stainless steel tubing. I bought this kit from the weld monger store. I'm using a ck worldwide 17 torch and a Prime weld 225x. I was having trouble with gas coverage and this kit solved it.

In this video I make some pie cuts out of 304 stainless 2.5" tubing to connect my stainless headers to the turbocharger. I first tack them together and then tig weld them together. I am building a turbo kit for a 305 chevy small block. I am using Flowtech up and forward headers and an Ebay GT45 turbo.

In this video I start building my turbo system. I start out by making a bracket to hold my GT45 turbo in place, in order for me to run the stainless tubes to the turbocharger. The engine is a stock 305 chevy. I'm using flowtech up and forward headers that are made out of 304 stainless steel.

In this video I paint an iron 2 barrel intake manifold. The manifold is for a small block chevy. I sandblast the intake and then paint it with VHT engine enamel. The color is cast aluminum, I was trying to make the manifold appear to be aluminum. I will be using this intake on a 305 chevy to make some vids on 2 barrel rochester 2gc carburetors.

In this video I paint my chevy 305 with VHT engine enamel. I do the best job I could, but the engine was sitting in my garage for a few months. It got a little rusty and a got some oil on it. I'm going to be rebuilding this small block chevy soon. I just have to save up the money to do so.

In this video I show how not to remove broken studs on small block chevy exhaust manifolds. I use erwin bolt extractors which was a fail because it just broke the ends of the studs. Next, I try to drill out the studs and extract them, and that was another fail. Then I do something that I do not recommend to anyone, I drill the hole out for the same size tap as the original bolt. I some how get ...

In this video I press out a wrist pin on a connecting rod. This is a stock rod and piston out of a factory roller 305 chevy engine. All press fit sbc rods should be the same, whether it's a 350ci, 400ci, or 327ci. I would not try this method if you were planning on re using the pistons.

In this video I talk about preparing a chevy small block for rebuild. I have a factory roller 305 chevy and I got it bored .030" over, I got the crank turned. I also had the block checked for cracks and the line bore checked. I know I'm taking forever, but I assure you this is not my first small block chevy build.

Harbor Freight steel stamping set

small block chevy spun rod bearing

305 chevy heads; 081 castings vs 416 castings

Predator generator inverter 8750, setup and first start up.

factory roller 305 small block chevy rebuild. update

Custom built chipping hammer metal fabrication project

how to remove pistons and crankshaft on chevy small block 305

square body chevy truck project, removing the heater box

Sqaure body chevy truck project

Diablo 14 inch steel demon blade, cutting 16 gauge stainless steel tubing

How to remove valves on small block chevy heads

Factory roller 305 small block chevy rebuild

Factory roller small block 305 chevy vs non roller 305 chevy

Utilitech 4ft LED shop light 4000 lumens

Flowtech turbo headers for a small block chevy