Видео

hahhaha, interesting 😄🤣

hello sir, we don't have shopee store. Any further questions or inquiries, please feel free to contact us by wechat or whatsapp: +8613310865590 , thanks.

@@savathsorn1108 nope sir, this panel is not from Hochiki 🙂

Ebay (cheaper) or Fire alarm sites (expensive)

Сколько кнопок ручного извещателя.

do you mean the connections ? you can contact us by whatsapp : +8613310865590 for any help with our fire products, thanks.

😃🤝

thank you 😊🌹

wires connect to terminals of CAN-H and CAN-L between panels

90-120 dB

Hello Sir, as in the vid, this device is simply with 2 cables, one is for 220vac power, the other is with a socket to connect to the valve directly, the valve can be installed to gas pipeline.

🤣🤣🤣

Hi, can use a programmer to change the sensitivity

Hello Sir, please kindly check the below link of this product: www.alibaba.com/product-detail/AS-DSG-100-Industrial-Audible-and_1600311166137.html?spm=a2747.manage.0.0.73c871d2PxvECD

Hello Sir, the cable is used for communication purpose, to transfer information between two devices. It's RS485.

Hello Sir, power off to reset it.

Hi, do you mean how it activated ? we used a smoke tester to trigger the detector

thanks 😀

@@ansorl no problem

thanks 😄

Hi, Joe A Repeater panel is an annunciator. It is in a location that is remote to the fire alarm control panel. It can report fire alarm and fault alarm messages.

😀😀

thank you Jennifer 😄😄

Hi, this is our conventional and resettable manual call point. You can use screws to fix it on the wall. For wiring, it's 4 wire connection: power line + signal line.

hello Sir

Hi Rocky, modules are used to connect other external equipments to addressable fire alarm panel. For convenient talk, I can send you the modules technical manuals by whatsapp: +8613310865590

They aren’t pull stations. They are called call points

@@nbfs0001 I have never seen one

@@FirstNLastN They are used instead of a pull station almost everywhere outside America.

@@mjyanimations1062 and canada

Hi Felix, sorry for my late, you can contact me on whatsapp: +8613310865590 for prompt reply. For your question: if you are using MN3010 panel, it's not available to expand address capacity on the panel. You can use another panel for it, and make the two panels interconnected.

Hi Rocky, our panel loop 1 has 100 / 200 /324 address for option.

@@ansorl how to adjust panel loop 1 to 324

@@rockygalgo9385 Hi Rocky, sorry, i didn't get your meaning, adjust ? do you mean configuration or operation ? if you buy the panel with 324 address, then you can connect to the panel for less than 324 fire devices . You can contact me on whatsapp +8613310865590 for detailed discussion if need.

thanks for your comment

Hi Gopi, sorry for my late. My email address is: firesafety@ansorl.com could you please get contact with me and then i will be able to send you our brochure and datasheet of this addressable fire alarm system.

Thank you Mani !

Hi Rocky, I am sorry for my late reply. Could you please send your requirements or questions to my email address: firesafety@ansorl.com, or contact by whatsapp/wechat: +8613310865590, so that I can reply you timely. Best regards,

Hi, repeater panel connects to addressable panel, there only to connect 4 wires, 2 power lines (24VDC, GND) and 2 communication line (485A, 485B). Any further qestions, feel free to email us firesafety@ansorl.com

@@ansorl what problem repeater offline mam

@@rockygalgo9385 1. make sure the repeater panel has been registered in the fire alarm panel 2. check the JP3 dial switch on the back side of the repeater panel, the eighth dial switch should be pulled to the ON position

@@ansorl how to the repeater panel registered the fire alarm panel

@@rockygalgo9385 Please refer to the fire alarm panel technical manual, page 23, part 4.1.5 indicating panel setup, there are detailed instruction.

evet adresli sistem

Sim, senhor, somos fabricantes de sistemas de alarme de incêndio. Tínhamos clientes do Brasil. Sinta-se à vontade para nos contatar para suas dúvidas

Hi, it's similar appearance, this model with 3 different alarm tones for option.

Hi Sir, our model bell supports 24VDC or 220VAC, and yes 120V is also good.