Видео

Remove clutch cover, centre floor cover and right side floor bolts, prop up floor with a short piece of 2x4, and hook front plastic fire wall by that corner bolt hole, pull up slightly ,couple of inches or so. Now you can remove shaft by moving it back to get around brace and go straight out front without taking anything else apart.

For anyone about to do this job found an easier way to do it, when going to remove prop unbolt and pull it fully towards the bull bar until the part on the rear diff spline is completely off then push front diff back into position and rebolt which rear of prop is off the rear diff. Then get the front of the prop off the front diffs spline then you should be able to unbolt front diff and pull it towards the bull bar and upwards almost as if you’re turning it 90° and you should have enough space to pull it through the front once you’ve removed the bull bar. Saves you having to disassemble the full clutch assembly

I'm at work right now trying to figure out how to do this and I found this video, thank you!!

Do think I should take the clutch out or skip that? what year is your polaris

why would you post this??

What kind of trike is it

fo show

yes!!!

should of panic reved

I was in 3rd, I run hipers now, super low weight and very strong. To answer the question how I like my yfzr, I love it! I own a 250r and banshee, I've owned a 04yfz, I've raced mx on a 07 trx. If your looking for a good mx quad, this one has the most impressive handling and stock suspension I've experienced. I ride mx all the time and I haven't touched the suspension yet! The efi is nice but its a hassle to tune if ur used to carb.

What gear were you in? 2nd or 3rd? just wondering

Where in NC is this?

IDK, I was filming...

how do you not hit that double to table landing!? so easy!

this description made me lmfao

did somebody pee right there and your calling it a river...LMAO

this is cool but you should mute the crashes check ot mah channel

Didn't break anything

that did not sound good

it really dosent look like a hard impact unless youve actually done it before, and i have i know that had to hurt.

nice 1 foot of air...

nice whip !

THATS WHATS UP..

Which pipe is that and did u need a programmer?

stock shocks?

Yea, I've read that Rossier and Dubach racing are top of the line for power gains. I've been thinking of new exhaust but im in the process of buying a trx250r rightnow to add to my collection. \ ,, / (> <) \ ,, / party

Dang dude I did a 60 foot duble and over shot it by 20 feet. It bend my axil,rim,frame, cracked my hip and hurt my pride lol. I was the first one on a quad to attempt it. anyways sick jump how do you like your YFZR I am planning on getting one

:O

that yfz450r gots some balls like right out of the corner its pulling mad hard dam i wish i had one

If you pause at the right time you can see the right rear wheel looks like its halfway undergound...as for your nuts....ouch. Id bet your tire pressure was too low....thats waht caused the bends. Cause that wasnt a huge flatland...Dont run hipers either. DWT FTW!

lol you should remove the chain

I can't believe that bent ur rims. My OMF's wouldn't even dent from that

woah man that was some river...i bet u pull out 6 pound salmon when there running...

where this track at?????

Yea, I'm not real sure how or why they bent but the track was hard packed and this video does not do justice to the actual impact, I hit hard enough to set off my roll over sensor and that is why my engine died. All I know is I now run hiper rims

Thanks

Yea, what is life without good friends?

Yea It was pretty risky but I live for the rush.

Haha, I didnt mean to be a dick.

@erskine3141986 omg, i think its the mississippi!

i love how everyone try's to stay outta the way of the camera you got some good friends their man

thats a huge river you got there

sweet!!

HMM, I dont know why the quality is so bad on this one, I use the same camera for all my vids.

Thanks, its HMF exhaust.

HMF

HMF slip on exhaust...Yea thats the 2nd set of rims I had bent so I switched to hiper carbon fiber!

happened to show up while some of his neighborhood friends were there so they let us in. All we had to do was sign a waivor and we could basically do anything we wanted besides ride into the big out door foam pit and ofcourse cause damage to his property.

Well me and a buddy were in maryland on a road trip and a friend of ours knows where Travis lives so we stopped in. You can go right up to his house but his actual compound (garage, foam pits, slip n bleed...etc) have a fence around them. We just

Thanks, although I'm confused? The 2nd one?...