Видео

Excelente video!!! Saludos desde Panamá

Working on similar ATX for a simple bench back up supply in place of my larger manufactured lab supply. Looks like that buck boost display is the way to go.

I am always confused. How a buck module will give you 30v when input is 12v?

*Consejo quitar esa música horrible que distrae sl estudiante*

Which line to add USB port?

I didn't buy.. to much pressing, setting and stuff. But good video

Gratidão 🙏

ZK-4KX DC DC Buck Boost Converter I can run a 12 volt 2 amp fan with it ?

Değerli üstad, benim zk4kx Modülüm 19v laptop güç adaptörü ile çalışıyor ancak en fazla 7.72 volt çıkış veriyor, bu sorunumu nasıl cozebilirim bana yardımcı olabilir misiniz, teşekkür ederim

Espectacular video sobre todo la parte final donde calibras los valores exactos de salida de voltaje y corriente. Te felicito .

I want to buy this product but how?

I dont get it. The blue "display" part can work itself. Why do you need the psu.

Is it possible to install two LEDs, green and red, to show when charging is in progress and when the battery is charged

Is that the PSU where "dummy load" on 12V or 5V power rail is not necessary? Cause I haven't see that you set the one? I see it was marked as PFC, which is fine. Thanks

why didn't you put a 3v as well as the 5V and 12V to make it complete

Gente vamos fazer o youtube dominado por JESUS! Cole isso em todos os vídeos que você vê! 💛ELE VIVE💛 🔥ELE ESTÁ VOLTANDO🔥 fixa??????????????????

Tem vários aspectos a considerar sobre esse vídeo. Primeiramente este conversor chega a 30v com 4 A de saída, achei o cabeamento de saída bem fino asim como o de entrada, portanto exigir a corrente máxima neste caso achei arriscado. Segundo achei tbm o cabeamento fino para os bornes de 5v, eu usaria mais de um cabo para este fim, de resto achei bem legal a ideia, eu usaria as tensões de +3v,+12v e -12v em outros bornes.

Can i use a ATX550W……..WT-4100cc ?

Creative video, thanks :)

the best video of demonstration and how set this module! thanks a lot Dude! hugs from Brazil!

Is there a way to get one that runs at higher amps? My PSU can put out 49amps and the charger I'm using accepts up to 30A

Really helpful video

Thanks for your video. Help me very much.

great video .. thanks .. how to make a rectangular hole on metal is something that i was looking for and this video helped a lot !!!!

Hi MT Electronics Great project. I've made you water path selector with the servo, could you check on Intructables i add a comment bellow.

I personally don't believe this is the best solution to achieve an ATX bench power supply. You are asking hobbyists to discard the {potential} majority, of the available current, of the power supply. Alot of PC PSUs are able to deliver more than 10-20A, on some of the voltage rails. Further, these ZK-4KX converters are merely adequate at delivering 3A, over a period of time, let alone 4A! I have tested one of these modules, to charge lithium batteries, & within 3-4 minutes the unit has gone into over temperature mode. Their specs are over-rated. At the very least, it requires active cooling (fan), if operating above 50%, of it's rated current. I would state using good quality potentiometers, to regulate voltage/current, would be a better option, to allow the full optimisation, of the regulated PSU.

By far, Simplest construction....

bro what was that music ?? please respond :v

Кусок говна вылазит. Lup и пиздец!

Muito bom , fiz a minha assim também. Parabéns

Tx you give me good ideias, greetings from Brasil.

Can work in short circuit for repair boards?

Hi, apparently you can use a phone charger wit this PSU, is that possible? ruclips.net/video/K4xzY3OY7RA/видео.html

Hello, Can i cut off the extra wires ? All wires of same color together as if they are a single wire. And then solder it of the end of each bunch as if it was one wire. I think high currents/amps better. And also can i use a spot welder for battery 18650 with this kit ? Thanks

I made this project so I could bend some acrylic but it keeps cutting off 🥺

👍🏻

Thanks for the prop guards. I tested them out about an hour ago: ruclips.net/video/rboLw69xQOo/видео.html

Nice Video, very informative. Can the Zk-4KX be reset to factory settings. And if so how is this done.

Thanx

Hi. Computer ATX has 12V. How out 28v ?

Music name plz

Nice music link

Can this one detect any paranormalities?

Hi , there.May I know why did you use 3.3ohm load to caliberate the settings

Bro I made in the same way you made for playing pubg but it does not gives that much sound you shown in the video🥵

Ups mother board

Does this Sensor measure a distance "point" or a surface? I want to measure liquid levels (i know liquids can be dificult) in a small shot glass. I dont know if this kind of sensors are measuring a surface of 1mm^2 or 100mm^2.

Looks strange with the display on the side. 😉

Hello, very informative video and web page. Thanks. Question: I saw in another person's video, he instead of cutting off the extra wires, fused all wires of same color together as if they are a single wire. And then he soldered the end of each bunch as if it was one wire. If I understood it correctly, according to him, it carries high currents/amps better. Is this true? Should one do that? Your module is up to 4 Amps. I was thinking of using a 20Amp module instead. If above is true, bunching of wires will be useful in that case. Thanks for guidance.