Видео

Your output current was inversed, because you have put the decoupling capacitor the other way?

In which website we get that simulation models, (Can you know where I get the spice model simulations for lm5030, sg3525)

thank u. u help me much for task

Muchas gracias por la explicación

not working Internal Exception: access violation in module 'SPICEINP.DLL' [00000647].

Merci beaucoup.😃

monostable please

There must be an error in the calculations for L1. A 60Hz transformer for 115Vacrms with L1=62,7uH ??? Primary currents would result in 5KApk roughly. Should be 627mH for L1 and 27.3mH for L2. Can you please comment? Thank you.

Si tu ne veux pas aider supprime cette vidéo c'est quoi ce bruit en fond ?

I don't have the "Hand" buttons in the upper bar. What's wrong with my LTspice? Do I need to enable any additional toolset in the settings?

this is not Characteristic Curve, this is Ic vs Vbe curve, the Characteristic Curve is Ic vs Vce

Thank you....

Does this way work if you have to recall a component in the future from library'

Thank you, good work. Are the considerations regarding the magnetic core for the next video?

Hello, This is an awesome video. Thank you! I did however have a question, for some odd reason my center frequency is off , by any chance do you know what might cause that

Thank you for the very clear explanation!

hi, why wonr any other digital pin work to blink an led????

can you share the document?

Thanks

You never covered the derivation of the values of the R4 and R5 voltage divider resistors. A total waste of 25 minutes if you do not cover the derivation of the gain of the feedback path required to raise the Q value to the required level to narrow the bandwidth. I imagine it is 10,000/250 = 40 but don't know why.

Can you make a simulation circuit for the Transformer inrush current analysis and calculation project?

du bist mein held

can you Design Efficient Pre-charge relay circuit to prevent inrush current in electric drives circuits

Nice and well explained. Thanks for sharing.

is this paid licensed software ?

HI I like your style, especially how do you connect the datasheet with the simulation. Nice work. I am using Kicad with Spice Simulator. (NGspice?) where you could get the simulation parameters of BC547? Can you share it somehow?

There is an error here. R=V/I, once, Rs=0.9V/5.78mA= 155.71 ohms.

why is the notch depth not 20db in the last simulation?

Does anyone know of a clear tutorial that you can link me to which shows simply how to import a SYMBOL and a MODEL into LTspice. I simply need the keystrokes and which folders to put these into. This should be less than a 3 minutes video. I just need to see the actual keystrokes, not hear someone talk talk talk for 15 minutes. thank you.

I can't understand why with linear sweep the cut off frequency was 10kHZ. Anyway thanks for this video.

Sir plzzzzz tell me how to import the spice model component nr100 bjt in lt spice

Not blink led...why

Didnt work both led stay on

hello, I have a question wether does this amplfier work also with input signal coming out of acoustic guitar pickup, so I can use it as a guitar amp... Thanks for response.

can i get your cell number actually i have an assignment for you

Very helpful, thank you

What will be the output waveform of this circuit if it is the hardware

can i use another transistor sir?

Thanks. This is a great video. Please keep going.

If we want to create an external circuit inplace of pothg what should be used ??

Thank you :)

Thanks for share your experience

Information Technology

Excelente conteúdo estarei seguindo e apreciando!

any video which simulate 1primmry and 2 secondary transformer?

can u please post a picture of circuit, i have to make this circuit fisically

I want to model SFH4510 IRLed in pspice It's from OSRAM and only has Datasheet of it i want to calculate schokley diode equation from it and calculate the N emission coefficient and IS please help me out with this.

Can it simulation a real time audio guitar effect pedal?

Could you please explain how multiply of 10 in this 20 Hz to 20 KHz range?

H! On the circuit on the right (the first circuit you made before analysing the current) I'm using only one 1N4148 diode parallel with a polar capacitor 100uf and I want to connect a resistor in series with the diode. How am I supposed to find the value of the resistor so that this converter works right? Thanks in advance. Also thank you for this video, it was extremely helpful.