Видео

Balls in this condition need to become house balls. Also this conditioning is the best method to go from a 15 lb to 14 lb ball.

i should have known when i saw the ball spinner this was going to be a bad video

I read what the manufacturer said but fuck it that takes too long

maybe a dumb question , but is it possible to air brush a bowling ball or paint it and then use it for games ?

This video should be titled “how not to resurface a bowling ball”

Good job my brother.....screw the haters

Why wouldn’t you do the entire ball with each step. That has to be the dumbest method of sanding anything I’ve ever seen

All these negative comments are why he never uploaded again. 🤣🤣

How much to resurface it

After this guy is finished the ball will roll BETWEEN the pins.

I accidentally glossed my matte ball how do I get the gloss off it can't hook anymore

Don’t listen to these idiots Marlon! Hope to see more videos bro! Jaydee

nice technique ,thanks for the helpful info

Does this reduce the weight of the ball?

Do people still bowl?

I bowl at this house, I've never believed this guy was good. I've never even gone in his shop. People have said he's horrible at drilling balls

How much it cost

OMG NOOO you destroyed the coverstock. this video should be titled "How NOT to Resurface a bowling ball" my friend has a ball spinner and he refurbished my white dot bowling ball and you cant tell the difference between that and a brand new one. he also filled the deep cuts and painted it! in your video the ball is full of grid lines and the reflection is stretched and blurred. It looks nothing like new. it looks like a scratched ball with polish. and you made it like an egg by shaving it.

1) Big flat gouge on the ball that you removed a TON of coverstock for when you could've just plugged that small hole and done a PROPER resurface. 2) You don't have any grid lines on the ball -- if her track flows with the grain of your sanding lines, it's going to hook much less/read too late; the opposite being the case if they go against the grain. 3) I would not be surprised if one took a surface scanner and read a bunch of wacky grits on the ball: one spot might say 5500 while another will read like 1500 because you didn't bother to surface the ball properly on all four sides. That's kind of part of the reason the manufacturer recommends it. Overall this ball is COMPLETELY illegal for use in any sanctioned league and your PSO license ought to be revoked. You should've responsibly informed the customer of the proper solution (clear resin plug) or at the very least tell her this is actually a 30-45 minute job when done right. Instead you ruined a bowling ball and look like an ignorant fool on RUclips. Bless.

You should not shave the ball,and 100 grit is too low. i would suggest beginning from 360. And when you polish you better polish 4 times in different directions so the shine wont look like a car windshield. (stretched reflection)

You.idiot

I've learned a lot in the past few months and they sell these Pads on Amazon for about 15 dollars for basically a new ball not bad. use my link amzn.to/2S8CzqO or just go to amazon.

I've learned a lot in the past few months and they sell these Pads on Amazon for about 15 dollars for basically a new ball not bad. use my link amzn.to/2S8CzqO or just go to amazon.

Did you go out of business? I don't see any other promised videos..

Omg sitting here in NJ but bowled as a kid there at JIB. Late 60s and 70s. Will email you more. Really weird that I searched resurfacing a varethane ball and came upon this vid.

Damn ball killer bahahahaa

that ball sounds "tu gu dug-tu gu dug" along the lane... promise!!!!

Wow... let’s just hope no one tries this at home! This is not how to resurface a ball,

lol who is watching game of thrones in the background

So when resurfacing a bowling ball? Do you start with the 180 grit and finish with the bowling ball recommendation.

Well... i know where i WONT be taking my ball to be resurfaced.. lol

Bet it rolls down the lane like a football.

Just curious...does that put a flat spot on the bowling ball when you fix the gash on the bowling ball

💩

Is this something you do to a urethane ball?

Dude, you are scraping away the surface of what used to be a perfectly round ball

Can someone commet and tell me how much the weight is affected by resurfacing a bowling ball?

Dam you guys are brutal! Yes he is doing it improperly but I think you guys really trashed him hard.

All these pro ball re finishers commenting...wow shouldn't all of you be pleasing your customers with your perfect ball skills??

wish I had a ball spinner

Don't do what this MORON is doing!!!! Abrolon pads!!!!!

When the lady gets her ball back, it is 1 inch less in diameter than when she brought it to this dude.

My ball needs to be resurfaced... Good thing I gave it to someone who will do it right!

What's the name and location of your shop? I don't ever want to let you screw up my equipment.

@1:19 STOP RIGHT THERE. WTF ARE YOU DOING???

You are the MAN! I am getting my ball resurfaced Wednsday. Thanks

thank you

YO Mr Slick yar the ball is so smooooth Bahahahaha.

I wonder how his hand felt after that

This made me cry. Pro shops that do this right would clear plug the deep gauges. 2nd, the finished product, you can still see the log grid sanding lines in the ball. I would dislike this video a million times if I could.