Видео

Yo bro I’m running into the same issue with my piston any idea what was different between your 2 pistons ?

How did you tighten the selector? I’m having so much wobble and sometimes it’s shooting semi on auto

hey dou you still have the stl of the parts you product and if you have it would you be king enough to share with me this parts ?

Stupid question. Do you have the file for the Sleeve. Because I kind of need that too right now.

thank you!!!

I don't see anywhere mention these issues but I've had the inconsistency and in my v3 AK horrific midcap syndrome. After the second build I think I can narrow it down to the engine. Similar set ups with my inferno g2 drive nails in comparison

Hi can you share the file

I just managed to do this myself so can offer more details: Caveat: I did this on a CM.127 so check carefully that the instructions here seem to match. The catch looks identical. I also tried hard but couldn't manage to get enough angle on the spring without taking the gearbox out. Maybe you will have more luck. You need to put the release catch in first. Then slot the spring into the 'U' shaped groove that sits a few centimetres below it. The long arm of the spring goes on the left. (from the perspective of you holding the gun in your hand normally) At this point the long arm of the spring is both on the left and on the gearbox side of the release catch. Now for the tricky bit that makes it hard with the gearbox in: You have to slide top of the long spring arm across the release catch and into a cut out slot just to the bottom right of centre. !!! But do not leave it in this slot !!! Push the spring all the way through the small slot to the trigger side of the catch where it will spring back a little against a raised edge on the trigger side. Job done. I noticed that the new spring/catch that I bought from patrolbase.co.uk has a slightly different shape. Possibly to make sure it goes through the cut-out slot more easily. I am wondering if some were coming out of the factory with the spring in the cut-out and not fully push through. Though the new ones also looked harder to get in the U shaped groove. I refitted the original first and then couldn't get it out again easily. Which I took as a good sign it was solid anyway. I am expecting this to fail again as it looks like a really poor design that is prone to failure. Time will tell.

Mine fires all BBs left. Good to know it's a known issue, so I won't waste time on resolving, or buy another one. P* F2 just moves into prime spot. Shame, as I love the Titan II 😢

I think I have the same issue and it was brand new out of the box. Could you share a link to that tool you have modified to take the bolt apart? TIA

Why didn't I see this video before I bought this stupid thing. Every single bb does exactly what you said, it either goes right or left, repeatedly. We shouldn't have to buy or 3d print extra shit in order for a product to work. So frustrating.

When you 🪛 back the stock tube, you tightened to the max, or you leave a little gap to fit the cables?

Do you have the stl file for the sleeve?

Which part was out of spec? I've got one of these Pulsars and cannot get it to fire straight consistently. I've already had a replacement front part of the engine as the one I originally had was under sized and rotated on the gearbox like yours did. I did find a solution to my problem though........a Wolverine MTW. :)

Hey! I’m wanting to put an f2 in my Krytac and I was wondering if the cylinder part was easy to grind / dremel out. Thanks

HI! Would you be kind enough to share 3d print file of the sleeve you made?

Hey! Would you be kind enough to share 3d print file of the sleeve you made?

Hi mate Just watched your vid I saw the comment the engine was out of spec but I had a similar problem with my specna arms and a wolverine engine it’s turned out to be the bb retention arm on the maxx hop unit so I removed it and it fed flawlessly after that

What's your thoughts on the engine compared to other equivalents or other solenoid engines, i got a polarstar jack in my gel blaster over in Australia

Awesome video! I'm about to do this exact work, do you have a parts list by chance?

probably the WORST how to totorial on the web, coudl not see a god dame thing

Unfortunate, without this issue it would be a good gun. Thanks for sharing with us

Hi what kind of electronic board did you connect?

Hi what kind of electronic board did you connect?

It turns out this engine was out of spec.

Really wish you knew what gears you used 😕

Would installing a jack be the same procedure or different?

Thank you so much for the guide! I just got one of these tho im planning on putting in a Leviathan instead of a Titan into it but this helps out big time on the how! Do you have experience modifying the timing on the recoil system yourself?

How is the long term? Looking at putting a gate aster in mine.

Sup! If I put a titan in a TM recoil shock, does the bolt catch and bolt open function still works? Thanks

What did you do with the spring guide?

which way youre putting the spring in the gun? idk how to put it there

Pointless video of no help.

Hi, have you a link please for this mosfet?? Thanks

Can you plz help me with my Arcturus m4 think I need new trigger switch and can’t find one anywhere

is it possible change spring without dissambly gearbox?

Can you suggest a "valve key" to open the solenoid? I can't seem to find one I think would work.

Thanks for the helpful video! So, is all the micro switches breaking due to trigger over travel? Btw, that’s a cool soldering station with the built in alligator clips!

Jesus dude. Just leave the narration out next time.

Fake guns. Grraayyyttt

Hello, could you please tell me why in some assembly after installing the titan, the nozzle that usallyin stay in the back position became in the front position? Tks and sorry for my english

hello bro what you suggest the MOTOR ? hop up? tight barrel?

I have the same prob on my cyma mp5 platinum cm.041g. My trigger react only sometimrs and if Im shaking my replica it firrs but ecerything else is as you show in video. Connect battery it plays sound but after that nothing else.

Hey, can you link me the diode that came off? Mine did the same exact thing smh

Can you do the same stuff on my mk18??

Hey man! great video! I'd like to ask about the wiring. I'm gonna be doing the same build as you did here with some extra upgrade parts, but I saw you put in a rear wired gate titan instead of a front wired one. Is there any benefit to doing so? I'd like to not have those spade connectors and just have straight wires going from the gearbox back in the stock but was wondering if that would be better with a front or rear wired unit like you showed?

Ive been looking everywhere and cant find any info about this but have you seen or tried to install this hop up to a ARP9?

This problem has sadly happened to me, is it worth replacing just the switch? Has the new switch held up since repair, or has it broken again?

wrong connection on the motor end...

Hey, did you install this with the stock G&G Nozzle? Also, which model Maxx Hop-unit did you use? The MI or ME? great video man!!