Видео

Does that silicone harden?

Kool , now all i have to do is find out which relay to pull i have a 2010 malibu

Those grinds will mess up your kidneys!

Those are called axial and radial capacitors.

Go faster no thanks there fast enough as it is and dangerous

You need to prime the gas side by pressing the button on the gas regulator

8:28 I wonder if the vacuum actuated gizmo advances the throttle off idle.

10:10 Details shown how propane enters the CARB. 1/8" copper tube directed to front side of CHOKE plate.

Hi Shawn: so 1) the higher voltage doesn’t damage the caliper? (I can believe that since most 1.5 and 3 V circuit parts are dual rated and the low voltage allows them to both work, but not all!) and 2) you said how long you get now, but how long were you getting before? That 3 months seems close to what I thought my Harbor Freight is getting with 1.5V, so how much is the advantage really?

Why would you change from a puncture proof tyre to a pneumatic one ? May be cheaper, but way more expensive in the long run when you have to call breakdown out for a puncture on a regular basis 🙄

And, if you don't feel like destroying your chuck. You can soak it in PB Blaster and unstick it yourself 😂

There is nothing in here ;)

I missed what you did to fix the inverter panel. How did you know what e-parts were bad and to replace them. I might try mine before I buy a new panel. Thx

What scooters is that

Saved me so much time many thanks.

"use your air compressor" lol

Thank you😇

How did you get the rust off?

What paint did you use ?

Husband and I have a window ac unit, we’ve cleaned the coils and even put vinegar in there.. the smell still comes back

And what about the float height of this carburetor?

Sounds like a good idea...i wonder how and what to use to get that glue out of AVR and replace the capacitor...

I have to upgrade mine with t9900 as I want to install docker which cna only be installed on machines supporting virtualization. My current processor is t6600 . Any thoughts?

From where did you get thw drivers?

I agree the fans an issue, problem is there's only 24volts dc on the feed motor most of the CPU fans are dc12volt the fan in the unit is 120ac volt it's the same in a microwave

I think the 2 screws on the dovetail are meant to help snug not tight. Then the ones from the side are meant to push it again so its snug but not tight. Doesnt make sense to tighten the ones at the back because them you cant adjust it.

Thank you for sharing my friend, really enjoyed it 👍👍Happy day

I have no spark. I checked coil, plug, switch, ignition assembly replaced. Still nothing. Any ideas?

Wait, but if you squirt the water through and blow it with the air, wont it stay in the AC and mold will develop inside overtime?

So I have to build a new one basically ?

Great job 👍!!

Not one of those large capacitors on my inverter were bulging. Mine has 6 large ones and they all look brand new. What else could it be? My inverter is the 8750 Predator from harbor freight. I see no burn marks anywhere. All my wire male and female connecters were snapped in pllace. The inverter module looks brand new yet the generators "no power" light is on.

Love how they be like 80 with motor from rock auto kinda played your self with the used one

This is the Onan generator I just rebuilt. ruclips.net/video/W-GJD1fZcdM/видео.htmlfeature=shared

Nice video thanks for helping. I just rebuilt an own generator 4K. Runs great and I have the remote start. I hooked that up from watching your video. Thank you ! I am trying to get the light and the and the hr. tack to work. I’m having a hard time trying to figure that out. It’s an old-school one from the 70s. I’m not sure if the tachometer and light hook up to the switch and then from the switch to the generator to 5 and 6? Any help would be appreciated, brother!

EG 1800X AC out put no 😭😭😭

Cute pup ❤ hope all is well havent heard from for a while!

The Relay on the Printed Circuit Board (Black Box ) controls the Transformer Primary Input 120v Ac Voltage when you Pull the Trigger on the Welding Wand Torch it Closes the Relay and Feeds 120V Ac to the Transformer Let Go of the Trigger Relay opens Cutting the 120v Ac Voltage to the Transformer That's why there NO Voltage to the Wand Torch when the trigger is not Pulled . Another Upgrade that helps these welders is replacing the AC Power cord which is only 16ga to 14 or 12ga

Any chance you know where the correct breaker is? Ours runs but for some reason the microwave isn’t working this year with the gen otherwise it works plugged in.

What are the valves set at? Intake and exhaust.

i'm looking to put snowblower tires on the back of my rascal to give it a little wider stance and more off road capabilities. i'm going to try using the front forks and wheel from an 8" kids bicycle in the front fork head tube to give it a bigger front wheel if it is close enough to make it work. you might try something like that if you haven't upgraded by now.

Hola...buen trabajo...los cables son de cobre ? Y q medida ?

Thanks

The downside though, the motherboard will only support a maximum of 8 gb DDR2 memory. (2x4gb) I did the same to mine, but ended up scrapping it and saving the CPU for another project. T9900 was a great chip, but theres much faster stuff paired with faster northbridges out there nowadays. Great video!

If you solder in a button on the bottom spot on the board you can change between 11 different modes including thermometer and counter, stopwatch, decimal place change and others.. theres a calibrate but dunno how to use that mode. But you can wire in a reset button on the middle 2 pins on the little 5 pin deal which is needed for some of the other modes. Not sure where the thermistor would go on the board but maybe where the reset switch goes .. may need to solder in some supporting components for that mode cuz it just reads 32°f or 0°c and doesnt change..

Wow Sound good, Thank you for share ❤

not to rain on your parade but I took you speed control . by cutting the bottom of a used & upcycled k-cup I added cruise control to my Afikim C4 & due to slip the otherday on my ride I discovered my C4 has a throttle engaged on start beep code.I had speed c. engaged & accidentally turned off power with C.C. still on so C4 wouldn't start till I turned it off. I love my C4 hope to get a S4 some day. thanks for ideas. I am turning my ol Pride Rally 3 wheeler into 4 wheel total custom will be going to 26" bicycle wheels & tires maybe using sets of 2 per hub to have plenty of weight capacity . body will look like a micro mini 1922 Ford TT C Cab panel delivery truck. wish me luck I'll be watching to see what you have next. really looking forward to your retreading tires that you talked about on here

Frankly, very difficult to see. Perhaps different color wire? I appreciate the help, though.

Hey Shawn I was wondering if I can swap a brushless power head with a brushed power head ?

But still it can't be started when warm, got to wait half a day before it can be used again.