Видео

It is selfmade. See here: ruclips.net/video/3tLdlrRCOXo/видео.htmlsi=QTimrYZTxeFYiDFv and here: ruclips.net/video/_ce_BMJzpNU/видео.htmlsi=E4orD10Pua4-NBZS

Actually, when I remember corectly these wings in this case are made out of 1 piece of foamboard and a balsa stringer. The foamboard gets a kink inside, then some tape for protection on the outside and then is bended over the edge of a table, over the stringer and finally fixated with a little epoxy. Normally I use two sheets, but indeed I answered wrong in a previous comment

Aeronaut Depron 6mm for the wings and 5mm Vector Board for the Fuselage (except the top, this is also Depron). The engine covers are also Depron

@@scalercmodels9261 if use cardboard is it OK or will there be bad consequences

Precise build and right center of gravity etc. is certainly more critical than the choice if the materials. I have never used cardboard, but have seen successful builts

Thanks! It is my own design. Actually, the mold was used before for the fuselage of a Focke-Wulf FW190.

It does not always work as good as seen in this video. I have fails from time to time. I experienced, that Makrolon seems the best Polycarbonate (for me). I cannot say why, but it works a bit better than others. Pre-drying is also key. I pre-heat my molds only slighly before with a heat gun. A strong vacuum and being very quick from the oven to the mold is also a success key. And furthermore... it took me quite a while and several attempts until I had my 1st acceptable result.

@@scalercmodels9261 Thank you for your response and precision, I understand that success is not 100% guaranteed every time, but already after the 3rd attempt I am very happy to have managed to get my first body out, I understand that the speed of the gesture is essential, I have already reduced as much as possible the delay between the oven and my installation, I still have to practice to try to reach your speed and improve everything that is possible for me to improve, in any case thank you for sharing all that, for providing us with all the technical points and the feedback from your own experience, I confirm it to you, this allows someone who wishes to also achieve things with this technique ... I follow your channel with attention and admiration. Best regards

Would be a nice one, indeed. Just time is lacking...

@@scalercmodels9261 what do you mean?

I mean this is just a hobby. Work, family... there are other👍 duties as well

@@scalercmodels9261 I feel you I might do one myself

But I don’t have a big enough house

Was genau möchtest du denn wissen?

@@scalercmodels9261 wie man das baut

Meinst du jetzt die Karosserie oder das Chassis...? Das Chassis ist ein Baukasten und die Karosserie, schau mal diese Videos auf meinem Kanal, hier zeige ich wie ich diese baue bzw. tiefziehe: Ferrari 499P ruclips.net/video/3tLdlrRCOXo/видео.htmlsi=SzjMfGPMPfPFs0QX Porsche 908 (deutsch) ruclips.net/video/zuDupRlB_fg/видео.htmlsi=FGi83si2mE9MK604 Ferrari 156 ruclips.net/video/HWIHoM3zpb0/видео.htmlsi=RjOdgBHXJAw3L_kO Ferrari 512S ruclips.net/video/X2ltUkvZ4uA/видео.htmlsi=5pF-z3lCf2jU5dt1 Ferrari 312 B3 ruclips.net/video/nDUKevQiTCo/видео.htmlsi=l1K1eVR7qSSyhp21 Ferrari 250 GTO ruclips.net/video/nvHWBZzvRko/видео.htmlsi=k1zNxAUOWFHq-1ct Aston Martin DB4 GT Teil 1: ruclips.net/video/LfOmvEuLiX4/видео.htmlsi=CLKzqsJos-TlC2IK Teil 2: ruclips.net/video/EKdffADFFGo/видео.htmlsi=KX1zX1l4pDL31pnc Teil 3: ruclips.net/video/VQw7nK9zNTE/видео.htmlsi=F8Tjd2RZljns5PIE Porsche 963 Teil 1: ruclips.net/video/WI_sH1R15QI/видео.htmlsi=4Fkmz9vegB45HBjQ Teil 2: ruclips.net/video/S6nKj8GSeyU/видео.htmlsi=i9LeXKaluo0-De8l

@@scalercmodels9261 einfach das ganze auto

@@scalercmodels9261 könntest du einen link zeigen wo man das chassis kaufen kann

Thanks, will do!

Thanks! 🫶

Thanks! If you continue with your project, I'd be interest to see your results. The GT40 is also still on my bucket list 😀👍

They are selfmade - as the complete body is selfmade from scratch

​@@scalercmodels9261thanks, yes I have watched how you make bodies. Very interesting. Please can I ask you which PS colours you have used for the red and the yellow paint?

PS2 & PS19

Backed with black each

Thanks!

No, it's only hobby 👍

3-view prints of the original car and a bit of experience

In total approx. 3-4 hours of work from the first coating until it was done. But not in one go - including the time needed to dry the filler and/or the spray, it was 2-3 days. It's like filler - sanding - filler - sanding - filler - sanding - zincspray - sanding and then it depends if you still see dents or bubbles, maybe again some filler and sanding and the very final is always zincspray and sanding with fine sandpaper (400 or more)

Thanks!

Me

@@scalercmodels9261 you could make bank on them if you choose to make mass produce them.

A 15 years old Alfa Model 60mm EDF. Not very powerfull but good enough for such a light model

@@scalercmodels9261 Thanks a lot again !

Tesa tape

@@scalercmodels9261 Thanks a lot

In principle start woth a chassis which would suit the car/body in the best way (width/wheelbase and height). Then search for blueprints or drawings of your dream car and adopt it to the chassis (maybe it needs to be a bit wider or longer to fit). Then make up you mind if the shape of your car allows the mold to be on one piece of if you need separate sections to take it later out of the body. A 1:18th or 1:24th model also helps to find the right shape. In my channel you find many videos about different mold and bodies which I made, so you can get roughly an idea about the process

Magnets

No, this is only hobby 👍😀

I made it myself

No, only YT

@@scalercmodels9261 Can you make an F1 1/8 body?

Thanks for the credits!

According to my experience, it doesn't make a difference if painted or not. PETG is in general more brittle than PC.

@@scalercmodels9261 Researching this because my bodies were cracking and breaking soo quickly, I don't remember where I found this but I tried this and it works amazingly well. after the painting is complete, you should line the inside of the body shell with Mesh Wallboard Joint Tape, then cover the Mesh Tape with Shoe-Goo or Goop that is found at Home Depot. After doing so, I have found my RC Bodies are lasting 10,000 Times Longer!!!!!

I wasn't sure if it would look good on these Hypercar bodies. So I made the body first without it and maybe I will use a pen liner to draw doors, hoods etc. I haben't done so yet but I'm still thinking to do it...

The real car had wide fenders around the front wheel. I used screws to fixate this part because I wasn't sure if the position is 100% correct for my chassis. If not, I could re-arrange them when pulling another body. But in the end, they were already right at this position

Because I used a heat gun in addition for difficult areas (ehilst the vacuum was still running), at some point it was too much, and a small hole was in the sheet (luckily "outside" the body. But I wanted to continue to form a concave area with the heat gun so I had to fix it with some tape to remain a vacuum

Thanks! 😊

Thanks! 😀

Color printer, thin paper, double sided sticky tape and clear tape to protect it

I' m really sorry, but this is only my hobby, I'm not a commercial seller