- Видео 43
- Просмотров 170 713
T.C.
Добавлен 4 окт 2021
Installation of CNC router 3020
This video shows the process of installing a CNC router 3020. The operating range of the router is 30 cm by 20 cm by 4 cm. The process is deemed to be similar to that of CNC router 3018 or the likes. It comes with is spindle that can rotate at 10,000 rpm at 24V. Please subscribe, like and share if you are happy with the video. The chapter list is provided as follows for fast access to specific content.
Chapters
00:00 unboxing
00:25 install the base frame
01:18 mount the y-motor onto the base frame
02:00 install the movable x-y platform
03:52 install the left support
04:38 mount the z-motor onto the spindle holder
05:15 install the right support
06:05 mount the x-motor onto the right support
06:30 m...
Chapters
00:00 unboxing
00:25 install the base frame
01:18 mount the y-motor onto the base frame
02:00 install the movable x-y platform
03:52 install the left support
04:38 mount the z-motor onto the spindle holder
05:15 install the right support
06:05 mount the x-motor onto the right support
06:30 m...
Просмотров: 106
Видео
Inspecting a defective dehumidifier: Panasonic F-YZF10X
Просмотров 51Месяц назад
This video shows a defective dehumidifier (Panasonic F-YZF10X) which, one day, was found to stop after operating for a while. The Alert indicator was turned on and the Timer 4-hour indicator was flashing. The video also shows the location of the sensor PCB which could be replaced for troubleshooting if it is suspected the board may cause the problem. Please subscribe, like and share if you are ...
Standards in EHR: Clinical Terminology Standards & Health Info Exchange Standards
Просмотров 132 месяца назад
This video gives a brief introduction to standards used in electronic health records, i.e., clinical terminology standards and healthcare information exchange standards, and discusses the relationship between these two types of standards by making analogy with a train of freight cars. Please subscribe, like, share and comment if you are happy with the video. Thank you. #ehr #electronichealthrec...
Installation of a DC water filter pump for aquarium pets
Просмотров 92 месяца назад
This video shows the installation of a DC water filter pump in an aquarium. The pump and its power cable is hidden in a PVC tube. The plastic water tube is also put inside the pipe to make it more tidy. Please subscribe, like, share and comment if you are happy with the video. Thank you. #dcwaterpump #filter #waterfilter #waterfilterpump #aquarium #aquariumpets
Solving water leakage problem of GREE split air conditioner (Fast-forward and muted version)
Просмотров 5763 месяца назад
This is only a 2x fast-forward and muted version of the original video, made in response to comments from viewers. Hope it helps as well. Original video: ruclips.net/video/wknz_2C9KU8/видео.html Follow-up video: ruclips.net/video/3feOelM5cXM/видео.html Please subscribe, like and share if you are happy with the video. Thank you. #Gree #split #airconditioner #waterleak #leakage #格力 #空調 #冷氣清洗 #冷氣維...
Astrophotos: Orion and Pleiades
Просмотров 1813 месяца назад
The video contains photos of Orion and Pleiades taken using a 72mm F/6 ED APO Sky Rover telescope, iOptron SmartEQ Pro equatorial mount and Nikon D5500 DSLR. Photos were stacked using DeepSkyStacker and the RGB of the stacked results were adjusted. #astrophotography #astrophoto #astrophotos #deepsky #deepskyobjects #orion #orionnebula #nebula #pleiades #ioptron #M42 #M45 #sevensisters #sevensis...
Installation of cabinet drawer slides
Просмотров 1645 месяцев назад
This video shows the replacement of cabinet drawer slides for an old drawer. Please like, share and subscribe if you are happy with the video. Thank you. #drawerslide #diy #drawer #cabinet #drawerrunner #cabinetrail
Sea of Clouds at Yunnan Ladder Field
Просмотров 226 месяцев назад
This is a time-lapsed video, taken using iphone, on the sea of clouds of Yunnan ladder field, China, on 2024-02-26. Please like, share and subscribe if you are happy with this video. #seaofclouds #yunnan #ladderfield
Repair of microwave oven: follow up
Просмотров 736 месяцев назад
This is a follow-up of a previous video (ruclips.net/video/cONWA9cGehk/видео.html) on Siemens microwave oven repair. It was mentioned in that video that the size of the shaft of the original motor and the replacement could be different. This video shows the use of a small piece of wooden rod to equalize the size of the shaft of the replacement motor to that of the original motor. Please like, s...
Wooden holder for remote controllers
Просмотров 1196 месяцев назад
This video shows the making of a remote controller holder using scrap wood. It can be hung on a cabinet and hold up to 9 controllers. Please like, share and subscribe if you are happy with the video. #remotecontroller #diy #scrapwood #remotecontrollerholder #woodwork
Cherry blossom at the Kyoto Gyoen National Garden 日本 京都御苑 2024.03.27
Просмотров 306 месяцев назад
This video shows the scenery of cherry blossom at the Kyoto Gyoen National Garden, Kyoto, Japan on 27 March 2024. Please like, share and subscribe if you are happy with this video. Thank you. #cherryblossom #sakura #kyoto #kyotogyoen #nationalgarden #japan #京都御苑 #京都 #日本 #賞櫻 #櫻花
Blossoming sakura at Yodo, Kyoto, Japan 日本 京都 淀 河津櫻 2024.03.22
Просмотров 746 месяцев назад
This video shows the blossoming sakura at Yodo of Kyoto, Japan. The video was shot on 22 March 2024. Please like, share and subscribe if you are happy with the video. Thank you. #sakura #yodo #kyoto #japan #cherryblossom #cherryblossoms #日本 #大阪 #淀 #河津桜 #河津櫻
A small table made using scrap wood and foldable legs
Просмотров 1757 месяцев назад
This video shows the making of a small table using a pieced of scrap wood and four foldable legs. Please subscribe, like and share if you like the video. Thank you. #woodworking #woodwork #diy #table #foldabletable #foldablelegs #scrapwood
Installation of Windows 11 to a newly built desktop computer
Просмотров 827 месяцев назад
This video shows the process of installing Windows 11 to a desktop personal computer built using Intel i9-12900K CPU and MSI PRO Z-690A DDR4 motherboard Please subscribe, like and share if you are happy with the video. Thank you. Disclaimer: The video serves not advertising purpose. No parts or sponsorship are received from suppliers. Make reference to the videos at your discretion. #windows11 ...
3D printed pistol model for Nintendo Switch gaming.
Просмотров 417 месяцев назад
This videos shows 3D printing of Joy-Con Pistol model which can be used for Nintendo Switch. The model is created by pspguru at Thingiverse. The model is available at www.thingiverse.com/thing:5410945. Stereolithography (SLA) 3D printing with resin is adopted. Post-curing using UV light is used to complete polymerization reaction. #3dprinting #nintendoswitch #videogame #videogaming #nintendo #s...
Brilliant You have saved a lot of people money. Easy step by Step video 10/10 Thanks
Thank you for your comment! Good to know the video helps.
😢😢😢water GREE AC
How do you remove the last back screw before getting to the drain?? I can’t find the angle
Do you mean the screw @04:32? You could use a long screwdriver, preferably with magnetic tip; may need to insert through the gap between the two copper tubes, or the space around them. Hope it helps.
No idea how to remove that one stupid screw that is impossible to reach
Do you mean the one at @04:32? Try using a screwdriver with long handle, and with magnetic tip, preferably. You may want to refer to this follow-up video: ruclips.net/video/3feOelM5cXM/видео.html
i did that and my case fans are stuck on one colour. i used MSI centre and no change. what have I not done?
Did you try pressing the button on the case? see @00:50
@@t.c.6036 yes i did that this morning, and all good thanks 😀👍
That's great.
You can also connect a wet vac to the outside drain tube and suck the clog and water out. I did this today.😊
That's an easy way out indeed if the drain tube can be reached from the outside; but for those who live in high-rise apartment buildings, the drain tube may not be accessible from the back.
What the video doesn't show you toward the end is that you really can't lift the unit up to access the hole or clean the unit because the copper lines will get twisted. They don't show the opposite side. Why have us remove the screws to lift the condenser and see the drain hole? What we did, is access the drain hole from the back, once the exterior drain line is exposed. We cleaned the drain line out and the drain hole going in. I was hoping we didn't damage the copper lines as this video didn't show you could possible damage them if you attempt to lift the unit.
Végre egy értelmes videó! Finally a sensible video! Thank you!
I want to see house of the dead played with this I have seen a few on Amazon with better design I just want to print of a good looking mount and blast zombies
This vid was a godsend bro not even the manual said how to connect it to the motherboard😭😭😭
That's great! Happy to know the videos are helpful.
thank you
Life saver water dripping stopper
Thank you! While I don't have the exact same model, you showed those hidden screws to take the cover off. I would have never found those.
Best vid I could find on this on RUclips. Thanks for making it.
Thanks very helpful. Life saver!
Where can I connect the pci power cable please ? I don’t have hard disk
I see. Then you can probably plug in a separate pci cable to the power supply and connect the cable to the RGB light controller. Hope it helps.
he said pci power cable but really its a sata cable so take your sata cable and put it in your power supply then connect it with the rgb controller power cable then plug the 3 pin connecter in jrainbow 1 or jrainbow 2
Thank you for making the clarification.
Mine is also squeaking a little. I think it is from the fan. What should i do
I guess it is because the left end does not sit properly back in, or there may be some slight mis-alignment around there (e.g. axle holder/support at the left) and the things do not click; you may want to double check. Hope it helps.
Dude underrated asf man, other videos are irritating and useless
Thanks for your comment! Happy to know the video helps.
Thanks TC. The video was very helpful. I'd have never gotten the thing open without watching your video. I was just a little frustrated with time pressure.
Good video, but . . . get rid of the irritating music and speed up the pace. Unless you designed this for joe biden.
Thanks for watching the video! Your comment is well taken :) I just made a 2x fast-forward and muted version. Hope it helps. ruclips.net/video/zt7yTIrHeOs/видео.html
Very good guide. Helped me do it myself
Thanks for watching the video. Glad to know it helps. Your comment is encouraging.
Thank you very much, this was the first usable guide to find those hooks at the top.
Thanks for watching the video and your comment. Good to know the video helps.
Just wanted to jump in and say thanks too. Your video helped a lot!
Good to know, thank you for your comment!
back flushing from end of pile with water , will clear all the path up to AC drain hole
better to take all out down and work on it
edit!
Can the blade fan be removed at this point for cleaning?
Not really, but you don’t need to do that. get a mini split cleaning kit from Amazon sized for your unit. It slips over the housing easily. You can remove the air vane as shown in this video. With a flashlight you should be able to aim it upward and see the blower wheel for inspection. If it’s dirty, get a can of AC coil spray cleaner at Lowes, etc. Spray it on the wheel, and let it soak for 15 minutes or so. You may need to manually rotate the blower wheel with a non-metallic tool to apply the spray to the entire wheel. After it soaks for a while, you can rinse off the blower wheel with a pump up bug/fertilizer spray bottle filled with water. Inspect for cleanliness and repeat if necessary. You will be amazed how much gook will come from the wheel. It’s worth noting, that if you lift the left end of the evaporator coil as shown in this video too far or too much, it’s possible to crack a soldered fitting on the pressurized refrigerant tubes. This will render the unit junk and require replacement of the coil, which is a very expensive service call. My guess is the unit shown in this video doesn’t get sufficient airflow because it’s too close to the ceiling and the efficiency isn’t optimal. There should be at least a foot of open space above the unit. Sometimes they have to be installed that way, but it should be avoided.
Last ditch effort taking it apart. Try to take a shopvac to the other end of the drain and suck out the blockage out of the drain tube
So to my understanding you can use the same connectors for cpu or vga. The connectors are thus interchangeable?
They gotta add that relaxing music cause they know if you had to look this up you are already f’n raging.
Facts
😂😂😂😂😂😂
Thanks for watching the video; will keep your comment in mind :)
Sans aucun doute la meilleur video ;) pas de perte de temps en bavardage inutile...les détailles sont claire et precis le tous en images marquer, remarquer ;) Merci beaucoup pour vos précisions, votre travail, amitié de france
Thank you for your comments. I am glad that you find the video helpful. Merci pour vos commentaires. Je suis heureux que vous trouviez la vidéo utile.
Good thing I have my Shark Messmaster to clean it all up LOL
❤very good! Made the job a lot easier. At a push you could just solder in the DC power lead.
'Promo SM' ❤️
Nice
faltou o link do conector
Test the gun please 😢😢😢
Thank you! I thought they forgot to send instructions and screws for my motherboard… then you showed me where they were in the msi case. 😅😂
I unclogged and drained my air con but the thing is it keeps leaking 20 to 30mins after it’s been drained only to take it apart and find out it’s full again any ideas??
Would it be possible that it is not just clogged at the drain outlet of the air con, but also the connecting ducts and pipes beyond that ??
why would you ever use a 3050?
3050 🤡
This whole comment section is just kid complaing about 3050 😂
because its a scam
@@JesseVlogs the price is bad but the card basically would run most game fine at 1080p with adjusted setting plus market in different country and a lot different too and people still trusted Nvidia more that why people didn't go with 6600 instead plus Nvidia still better for E-sport game than amd gpu due to latency build in for those game.
@@flexzii6772 its not just the price you can get better cards for the same price or even lower like all the 10 series cards are far better value and performance then the 3050 it just shows its just not worth getting at all
@@flexzii6772 bro any good gpu 100$ cheaper could do what you just described, and wym amd gpu cause latency???
3050 is pure shit
WHY 3050!!!
I still haven't figured out what is the attraction, it is just a big distraction to me. Flashing lights, whoopie !
This is really handy! I will definitely send these videos to my friends instead of having to explain it step by step, thank you.
Thank you for watching the videos. Hope it helps. Please subscribe, like and share. There will be further videos sharing my experience in installing Windows 11 in the computer. Stay tuned.
TaxCollector TB?
3050 aint no way
BRUUHi got a gtx 3050 cry anout it 😂😂🎉
@@officialneverfar i got rtx 760 trust me
I hope this is just a tutorial and not your actual rig..
That is 100% not all the way plugged in. I can tell by the fact that the connection for the 6 by 2 arent lined up, plus the latch itself is still raised and its not pushed all the way in. I think you might wanna double check that.
Sorry to nitpick but the powerconnector that you called "pcie" is a SATA power connector. Pcie would refer to the 6+2 pin connector that plugs into a gpu.