![Lime Laser](/img/default-banner.jpg)
- Видео 19
- Просмотров 11 433
Lime Laser
Добавлен 17 окт 2022
Видео
First service and Deep cleaning
Просмотров 39Год назад
The machine hasn't been serviced for so many years, Now its serviced Deep cleaned, and it's working 100% #deepcleaning #co2laser #lasercuttingmachine
Repairing a water damaged 1390 co2 laser
Просмотров 43Год назад
Repairing water-damaged 1390 Co2 laser in two days #limelaser #co2lasercutter #davidem #deepclearning
Installing Camera on Co2 laser machine Using Lightburn
Просмотров 1,7 тыс.Год назад
#thurnderlaser #co2lasercutter # lightburn #camera Installing a camera on a Nova 35
First Deep clean after years of usage (600x400)
Просмотров 47Год назад
600x400 from am laser, getting its first service and Deep clean after years of usage Please share,like, comment and subscribe #co2lasercutter #deepcleaning #lasercuttingmachine #davidem
How to upgrading Leetro controller into Ruida controller to work on Mac book
Просмотров 747Год назад
A New Ruida controller is being installed on a Client Co2 Laser machine as the client wants to use his Mac Book, Using Lightburn software #davidem #ruida #lightburn #macbook #co2lasercutter
1390 Co2 laser machine first Deep clean and Service
Просмотров 70Год назад
After so many years of usage 1390 laser machine is getting its first deep clean and full service #davidem #deepcleaning #limelaser #co2lasercutter #lasercuttingmachine
900X600 Co2 Laser machine (Final)
Просмотров 63Год назад
Refurbished Co2 laser machine finally done in 4 Days, machine is cutting and engraving 100%...and thank you everyone for sharing and subscribing
Refurbishing 900x600 C02 laser machine
Просмотров 44Год назад
Co2 laser machine getting refurbished #davidem #limelaser #lasercuttingmachine #deepcleaning
Repairing Laser Machine Co2
Просмотров 24Год назад
Driving to the northing cape to repair a laser machine , in a place called Port Nolloth .700km from Cape Town ...No client is too far for Lime Laser you call we deliver #davidem #lasercuttingmachine #artsandcrafts #co2lasercutter #engravingmachine
Reinstalling and Deep cleaning Co2 laser machine
Просмотров 42Год назад
After 5 years this machine Is getting its first Deep cleaning #deepcleaning #davidem
Deep Cleaning 600*400 laser machine
Просмотров 56Год назад
600x400 getting its first Deep cleaning after one year of usage #deepcleaning #limelaser #davidem
How you connect with mac ?
How much do the parts cost?
I paid R8500
@@limelaser3800 in the process of doing mine having to fit extra limit switches it's being a complete head ache!
So buddy, what was the problem?
3 wires going to the rotary ports
Kya without camera machine me m camera add ho jta h
please help me, I have a problem with the fact that I somehow messed up the whole machine, because I wanted to change the location of the Y sensor, which should check that the machine head does not cross the boundary of the working field beyond the edge upwards. The moment I moved the sensor so that the head always stops 3 cm below the upper right corner after turning off and on, the machine goes completely crazy and completely ignores the X and Y sensors and does not know the limits of the working area. (model: monor 7050 )
basically, I can engraving, I just have to manually enter the starting position of the head, but the problem is that when I end the project or turn on the machine, it completely shakes because it ignores the boundaries, also if the project crosses the boundary, it doesn't warn me but smashes against the side. Im so done
Thank you loads for posting this
Hi is the Ruida better than the Leetro?
Yes and No , Leetro gives more problems that
Plz make detail video
Servo or stepper which have long life
Servos are more accurate than the steppers, and with Servo, u can run ur machine much faster .However, motors don't really break most of the time is ur drivers or wiring
hello, we have with my gf problem that at start or when we click reset, the head ride to the up center of machine, and machine thinks it is top right corner, we cannot move to the real top right corner, and machine sometimes freeze or lose communication with RDWorks (or with pc) this all started to happen after power supply change, dont you know what to do with it ?
Having the same issue but for me my power supply wasn’t changed.. how do we fix that
@@joeoppong3419 we realized the problem is or better say was the x axis end switch, to be more precise, not in the end switch but in its cable.... the cable was simply broken in some place and it had not contact with mainboard we replaced the cable and the end switch and now it get beautifully into home position as it should
try resetting ur axis on the machine
Awesome bro
Nice working
Thank you so much
Awesome video